XLGシリーズ 3-260W 工業用X線ジェネレーター (featured)

XLGシリーズ

  • 最大出力電圧130kV
  • 接地基準フィラメント電源
  • 「ホットアノード」、正極性
  • ローカル、リモートプログラミング

*注: すべての仕様は予告なく変更される場合があります。最新版についてはこのデータシートの英語PDFをご覧ください。

CEマーク

3~260W産業用X線ジェネレーター

 XLGシリーズは、出力電圧範囲が130kVまでの安定化高圧電 源です。また、高精度な共振コンバータ技術により、リップルは 大変低くなっています。出力電圧及び管電流の安定度により、従 来の技術での性能を大幅に改善しました。このシリーズは、安定 したDCフィラメント電源を含む、X線用途に必要な電力制御及 びサポート機能を提供します。また、ローカル及びリモート・プ ログラミング、モニタ、安全インターロックや、短絡、過負荷の 保護回路も内蔵されています。

用途

  • メッキ測定
  • 鉱物解析
  • 蛍光X線

CE Marking

Specifications

(Ref. 128012-001 REV. M)

SPECIFICATIONS 

Input Voltage:

115Vac±10%, 50-60Hz single phase or

220Vac±10%, 50-60Hz single phase.

Voltage and Current Control:

Local: continuously adjustable from zero to maximum rating via a ten-turn potentiometer with a lockable counting dial.

Remote: 0 to +10Vdc proportional from 0 to full output. Accuracy: ±1%. Input Impedance: 10Mohm.

Filament:

Specify at time of order:

FH: 9A, 3V.

FL: 3A, 3V.

Preheat level is 0.45 amps in standby

Voltage Regulation:

Load: 0.005% of full output voltage no load to full load.

Line: 0.005% for input voltage range change.

Current Regulation:

Load: 0.05% of full current ±100µA from 0 to full voltage.

Line: 0.05% of rated current over specified input range.

Ripple:

0.03% rms below 1kHz.0.75% rms above 1kHz.

Temperature Coefficient: 

100ppm/°C.

Stability:

0.01%/8 hrs after 1/2 hour warm-up.

0.02% per 8 hours (typical).

Cooling:

Free air convection.

Metering:

Digital voltage and current meters (3.5 digits), 1% accuracy.

HV Output Cable:

10’ (3.3m) of shielded HV cable removable at rear.

I/O Connectors:

25 pin D-type for control interface with mating connector provided.

Dimensions:

30 to 60kV: 3.5”H x 19”W x 19”D (8.9cm x 48.3cm x 48.3cm).

80 to 130kV: 3.5”H x 19”W x 24”D (8.9cm x 48.3cm x 61.0cm).

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive.

FRONT PANEL STATUS INDICATORS: 

Overvoltage          Voltage Control Mode  
Overtemperature   Current Control Mode  
Regulation Error    Interlock Open  
Arc                      Interlock Closed  
HV ON: Red         HV OFF: Green  

OPTIONS

APT - Adjustable Power Trip  
AT - Arc Trip  
SS(x) - Non-Standard Slow Start  
NSS - No Slow Start  
IO - Instant ON  
LL(x) - Extra Length HV Cable  
SL - Slides

Electronic Component (Power Source)

XLG series is intended for installation as a component of a system. It is designed to meet CE standards, with conditions of acceptance often being: customer provided enclosure mounting, EMC filtering, and appropriate protection, and isolation devices. The XLG series is not intended to be operated by end users as a stand-alone device. The XLG series power supply can only be fully assessed when installed within a system, and as a component part within that system.

XLG INPUT CURRENT

Model 115Vac 220Vac
3W-30W 0.6A 0.3125A
40W-60W 1.2A 0.625A
70W-150W 3.0A
1.56A
160W-260W 5.25A
2.71A

XLG SELECTION TABLE 0.1mA, 0.2mA , 0.5mA

kV 0.1mA 0.2mA .5mA
30 XLG30P3* XLG30P6* XLG30P15*
35 XLG35P3.5* XLG35P7* XLG35P17.5*
40 XLG40P4* XLG40P8* XLG40P20*
50 XLG50P5* XLG50P10* XLG50P25*
60 XLG60P6* XLG60P12* XLG60P30*
80 XLG80P8* XLG80P16* XLG80P40*
100 XLG100P10* XLG100P20* XLG100P50*
120 XLG120P12* XLG120P24* XLG120P60*
130 XLG130P13* XLG130P26* XLG130P65*

*Specify FH for High power (27W) filament, FL for Low power (9W) filament.  

XLG SELECTION TABLE 1.0mA, 2.0mA, 3.0mA

kV 1.0mA 2.0mA 3.0mA
30 XLG30P30* XLG30P60* XLG30P90*
35 XLG35P35* XLG35P70* XLG35P105*
40 XLG40P40* XLG40P80* XLG40P120*
50 XLG50P50* XLG50P100* XLG50P150*
60 XLG60P60* XLG60P120* XLG60P180*
80 XLG80P80* XLG80P160* ---
100 XLG100P100* XLG100P200* ---
120 XLG120P120* XLG120P240* ---
130 XLG130P130* XLG130P260* ---

*Specify FH for High power (27W) filament, FL for Low power (9W) filament.  

XLG CONNECTOR 25 PIN

Pin Signal Signal Parameters
1 Power Supply Common Signal Ground
2 External Inhibit Ground=Inhibit, Open=HV On
3 External Interlock +15V at Open, <15mA at Closed
4 External Interlock Return Return for Interlock
5 Current Monitor 0 to 10V=0 to 100% Rated Output
6 kV Test Point 0 to 10V=0 to 100% Rated Output
7 +10V Reference +10V, 1mA Max
8 Remote Current Program In 0 to 10V=0 to 100% Rated Output
9 Local Current Program Out Front Panel Program Voltage
10 Remote Voltage Program In 0 to 10V=0 to 100% Rated Output
11 Local Voltage Program Ou Front Panel Program Voltage
12 Power Monitor 0 to 10V=0 to 100% Rated Output (Optional)
13 Remote Power Program I 0 to 10V=0 to 100% Rated Output (Optional)
14 Local HV Off Out +15V at Open, <25mA at Closed Connect to HV OFF for Fp Operation
15 HV Off +15V at Open, <25mA at Closed Connect to HV OFF for Fp Operation
16 Remote HV On +15V, 10mA Max=HV Off 0=HV On, +15V, 10mA Max=HV Off
17 Remote HV Off Indicator +15V, 10mA Max=HV Off 0=HV On, +15V, 10mA Max=HV Off
18 Remote HV On Indicator 0=HV Off, +15V, 10mA Max=HV O
19 Remote Voltage Mode Open Collector 50V Max, 10mA Max On=Active
20 Remote Current Mode Open Collector 50V Max, 10mA Max On=Active
21 Remote Power Mode Open Collector 50V Max, 10mA Max On=Active
22 Remote PS Fault 0=Fault, +15V, 0.1mA Max=No Fault
23 +15V Output +15V, 100mA Max
24 Power Supply Common Signal Ground
25 Shield Return Shield Return

Tables & Diagrams