SpellmanHV XLG Series 3W-260W X-ray Generators Rack Mount

XLG Series

  • Output Voltages to 130kV
  • Ground Referenced Filament Supply
  • “Hot Anode”, Positve Polarity
  • Local & Remote Programming

*Note: All specifications are subject to change without notice. Please consult the English PDF version of this datasheet for the most up-to-date revision.

Two Year Extended Warranty & RoHS Compliant LogosCE Marking

3-260W Industrial X-Ray Generators

Spellman’s XLG Series of X-Ray generators are well regulated high voltage power supplies with output voltages to 130kV and very low ripple achieved through the use of advanced resonant conversion techniques. Extremely stable voltage and emission current outputs result in significant performance improvements over previously available technology.

The XLG Series provides all the power, control and support functions required for X-Ray applications including a regulated dc filament supply. These units incorporate local and remote programming, monitoring, safety interlock, short-circuit and overload protection. 

Typical applications:

  • Plating Measurement X-Ray generator
  • Mineral Analysis X Ray generator
  • X-Ray Fluorescence X-Ray high voltage power supply

사양

(Ref. 128012-001 REV. M)

SPECIFICATIONS 

Input Voltage:

115Vac±10%, 50-60Hz single phase or

220Vac±10%, 50-60Hz single phase.

Voltage and Current Control:

Local: continuously adjustable from zero to maximum rating via a ten-turn potentiometer with a lockable counting dial.

Remote: 0 to +10Vdc proportional from 0 to full output. Accuracy: ±1%. Input Impedance: 10Mohm.

Filament:

Specify at time of order:

FH: 9A, 3V.

FL: 3A, 3V.

Preheat level is 0.45 amps in standby

Voltage Regulation:

Load: 0.005% of full output voltage no load to full load.

Line: 0.005% for input voltage range change.

Current Regulation:

Load: 0.05% of full current ±100µA from 0 to full voltage.

Line: 0.05% of rated current over specified input range.

Ripple:

0.03% rms below 1kHz.0.75% rms above 1kHz.

Temperature Coefficient: 

100ppm/°C.

Stability:

0.01%/8 hrs after 1/2 hour warm-up.

0.02% per 8 hours (typical).

Cooling:

Free air convection.

Metering:

Digital voltage and current meters (3.5 digits), 1% accuracy.

HV Output Cable:

10’ (3.3m) of shielded HV cable removable at rear.

I/O Connectors:

25 pin D-type for control interface with mating connector provided.

Dimensions:

30 to 60kV: 3.5”H x 19”W x 19”D (8.9cm x 48.3cm x 48.3cm).

80 to 130kV: 3.5”H x 19”W x 24”D (8.9cm x 48.3cm x 61.0cm).

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive.

FRONT PANEL STATUS INDICATORS: 

Overvoltage          Voltage Control Mode  
Overtemperature   Current Control Mode  
Regulation Error    Interlock Open  
Arc                      Interlock Closed  
HV ON: Red         HV OFF: Green  

OPTIONS

APT - Adjustable Power Trip  
AT - Arc Trip  
SS(x) - Non-Standard Slow Start  
NSS - No Slow Start  
IO - Instant ON  
LL(x) - Extra Length HV Cable  
SL - Slides

Electronic Component (Power Source)

XLG series is intended for installation as a component of a system. It is designed to meet CE standards, with conditions of acceptance often being: customer provided enclosure mounting, EMC filtering, and appropriate protection, and isolation devices. The XLG series is not intended to be operated by end users as a stand-alone device. The XLG series power supply can only be fully assessed when installed within a system, and as a component part within that system.

XLG INPUT CURRENT

Model 115Vac 220Vac
3W-30W 0.6A 0.3125A
40W-60W 1.2A 0.625A
70W-150W 3.0A
1.56A
160W-260W 5.25A
2.71A

XLG SELECTION TABLE 0.1mA, 0.2mA , 0.5mA

kV 0.1mA 0.2mA .5mA
30 XLG30P3* XLG30P6* XLG30P15*
35 XLG35P3.5* XLG35P7* XLG35P17.5*
40 XLG40P4* XLG40P8* XLG40P20*
50 XLG50P5* XLG50P10* XLG50P25*
60 XLG60P6* XLG60P12* XLG60P30*
80 XLG80P8* XLG80P16* XLG80P40*
100 XLG100P10* XLG100P20* XLG100P50*
120 XLG120P12* XLG120P24* XLG120P60*
130 XLG130P13* XLG130P26* XLG130P65*

*Specify FH for High power (27W) filament, FL for Low power (9W) filament.  

XLG SELECTION TABLE 1.0mA, 2.0mA, 3.0mA

kV 1.0mA 2.0mA 3.0mA
30 XLG30P30* XLG30P60* XLG30P90*
35 XLG35P35* XLG35P70* XLG35P105*
40 XLG40P40* XLG40P80* XLG40P120*
50 XLG50P50* XLG50P100* XLG50P150*
60 XLG60P60* XLG60P120* XLG60P180*
80 XLG80P80* XLG80P160* ---
100 XLG100P100* XLG100P200* ---
120 XLG120P120* XLG120P240* ---
130 XLG130P130* XLG130P260* ---

*Specify FH for High power (27W) filament, FL for Low power (9W) filament.  

XLG CONNECTOR 25 PIN

Pin Signal Signal Parameters
1 Power Supply Common Signal Ground
2 External Inhibit Ground=Inhibit, Open=HV On
3 External Interlock +15V at Open, <15mA at Closed
4 External Interlock Return Return for Interlock
5 Current Monitor 0 to 10V=0 to 100% Rated Output
6 kV Test Point 0 to 10V=0 to 100% Rated Output
7 +10V Reference +10V, 1mA Max
8 Remote Current Program In 0 to 10V=0 to 100% Rated Output
9 Local Current Program Out Front Panel Program Voltage
10 Remote Voltage Program In 0 to 10V=0 to 100% Rated Output
11 Local Voltage Program Ou Front Panel Program Voltage
12 Power Monitor 0 to 10V=0 to 100% Rated Output (Optional)
13 Remote Power Program I 0 to 10V=0 to 100% Rated Output (Optional)
14 Local HV Off Out +15V at Open, <25mA at Closed Connect to HV OFF for Fp Operation
15 HV Off +15V at Open, <25mA at Closed Connect to HV OFF for Fp Operation
16 Remote HV On +15V, 10mA Max=HV Off 0=HV On, +15V, 10mA Max=HV Off
17 Remote HV Off Indicator +15V, 10mA Max=HV Off 0=HV On, +15V, 10mA Max=HV Off
18 Remote HV On Indicator 0=HV Off, +15V, 10mA Max=HV O
19 Remote Voltage Mode Open Collector 50V Max, 10mA Max On=Active
20 Remote Current Mode Open Collector 50V Max, 10mA Max On=Active
21 Remote Power Mode Open Collector 50V Max, 10mA Max On=Active
22 Remote PS Fault 0=Fault, +15V, 0.1mA Max=No Fault
23 +15V Output +15V, 100mA Max
24 Power Supply Common Signal Ground
25 Shield Return Shield Return

테이블 및 다이어그램