XRB200PN400/2 Monoblock®
- 200 kV y 400 W
- Corriente del tubo de rayos X: de 0,5 mA a 2,0 mA a 200 kV
- Haz en abanico simétrico de 85° x 4°, ±1 %
- Entrada con corrección del factor de potencia a 0,98
- De 100 V CA a 240 V CA, ±10 %
- Acondicionamiento del tubo de rayos X controlado por firmware y con registro de datos
El modelo XRB200PN400/2 de Spellman es una fuente de rayos X integrada que opera hasta 200 kV y 400 W, ofreciendo a los fabricantes de equipos originales (OEM) una unidad Monoblock® compacta y lista para usar (*plug-and-play*) para aplicaciones críticas de inspección y escaneo. La unidad incorpora un tubo de rayos X de ánodo fijo con un ángulo de 15°, que proporciona un haz en abanico simétrico de 85° x 4°. Su circuito patentado de control de emisión garantiza una excelente regulación de la corriente del tubo de rayos X, logrando una estabilidad de dosis y una calidad de imagen líderes en el sector. Este modelo compacto cuenta con control estándar, tanto analógico como digital (RS-232). Spellman ofrece versiones personalizadas de esta plataforma para satisfacer los requisitos específicos de los sistemas OEM.
APLICACIONES TÍPICAS
Inspección de seguridad en aviación: equipaje facturado/EDS, inspección de vehículos, inspección de carga, ensayos no destructivos (END) generales
- Especificaciones
- Descargas
Especificaciones
(Ref. 128085-001 REV. B)
- X-Ray Characteristics:
- Tube Type:
Stationary Anode, tungsten target - Focal Spot:
0.8 x 0.8mm nominal (IEC60336) - Beam Filter:
Glass 2.1mm, maximum. Oil 18mm. - Beam Geometry:
Symmetrical fan of 85° X 4°, ±1% - Anode Angle:
15° - Input Voltage:
Power factor corrected input to 0.98. 100Vac to 240Vac, ±10%, 50/60 Hertz. 6 Amps, maximum - X-Ray Tube Voltage:
Nominal X-Ray tube voltage is adjustable between 100kV to 200kV - Voltage Accuracy:
The high voltage measured at the X-ray tube will be within ±1% of the selected value. - Voltage Ripple:
Ripple will be 1% of maximum rated voltage for frequencies ≤1kHz. - Voltage Regulation:
< ±0.1% for ±10% of nominal input line change
< ±0.1% for 0.5mA to 2mA load change - Voltage Overshoot:
kV overshoot will return within 5% of full voltage in less than 100ms. - Risetime:
The voltage and current risetime is controlled by a ramping circuit. Ramp time is less than 1.0 second from 10% to 90% of output voltage and current. - X-Ray Tube Current:
0.5mA to 2.0mA @ 200kV, 400 watts maximum - Current Accuracy:
<±1% of the selected value. - Current Regulation:
<0.5% at 100 - 200 kV, 0.5mA to 2.0mA - Arc Intervention:
Unit will detect a single arc but HV will not shut down. If multiple arcs occur (4 in 10 seconds) then the unit will shut down. - Filament Configuration:
Isolated high frequency AC filament drive operated in current mode with closed loop thermionic filament emission control. - Digital Interface:
The RS-232 and Ethernet interfaces allow for programming of the voltage, current and X-Ray Enable. Provides monitoring for voltage, current and oil temperature. Tolerance is 3%. - Control Software:
A demo GUI is available for engineering evaluation. - Operating Temperature:
0°C to +40°C - Storage Temperature:
-40°C to +70°C - Humidity:
10% to 95% relative humidity, non-condensing. - Cooling:
Heat exchanger with fan and oil pump. Customer provided +24Vdc @ 3A is required. In certain situations, external cooling fans of 250CFM may be required to maintain tank/oil temperature below 55°C. - Input Line Connector:
3 pin Phoenix Contact, p/n 1829167. Mating connector provided with unit.
Descargas
Suscríbase a nuestro boletín informativo de alto voltaje
Suscríbase a nuestro boletín informativo sobre alta tensión, que se publica trimestralmente con información relevante sobre tecnología y aplicaciones de fuentes de alimentación de alta tensión.