Generadores de rayos X industriales de 1200 W

Los nuevos generadores de rayos X de la serie DXM100 de Spellman están diseñados para aplicaciones de OEM de hasta 100 kV a 1200 W. Su entrada universal, tamaño de paquete pequeño y la elección de las tres interfaces estándar simplifica la integración de la DXM100 en sus sistema de análisis de rayos X. El circuito de control de emisión basado en un procesador de señal digital (DSP) proporciona una regulación excelente de la corriente de emisión además de una sobresaliente estabilidad.

Aplicaciones típicas:

• Aplicaciones típicas
• Medición de revestimientos
• Análisis de minerales
• Inspección de cristales
• Inspección de diamantes
• Inspección de alimentos o productos

Especificaciones

^{(Ref. 128107-001 REV. J)}

Input Voltage:

Power factor corrected input, ≥ 0.98 180-264Vac, 47-63Hz, 8.25A maximum

Output Voltage:

100kV, maximum

Output Polarity:

Negative-for floating filament X-Ray tubes 

Output Current:

12mA maximum

Output Power:

1200 Watts maximum

Output Voltage Regulation:

≤ 0.01% of rated output voltage over specified input voltage range

≤ 0.01% of rated output voltage for a full load change

Emission Current Regulation:

≤ 0.01% of rated output current over specified input voltage range

≤ 0.01% of rated output current for a change from 30% to 100% of rated output voltage

Filament is disabled when kV is <30% of full scale output 

Ripple:

≤ 1%rms at >20 kHz, 0.1%rms below 20 kHz

Stability:

≤ 25ppm/hr after a 2 hour warm up

Temperature Coefficient:

≤ 50ppm per degree C

Environmental:

Temperature Range:

Operating: 0°C to 40°C

Storage: -40°C to 85°C

Humidity:

20% to 85% RH, non-condensing.

Filament Configuration:

Closed loop emission control regulates filament setting 
to provide desired X-Ray tube emission current.

Output: 5.0 amps at a compliance of 10.0 volts, maximum. The filament loop is disabled when the kV output is less than 30% of full scale output to protect the X-Ray tube. Other filament levels available on special order. 

Control Interface:

Local Interface:

Potentiometers are provided to adjust filament limit and preheat levels

Remote Interface:

USB, Ethernet and RS-232 are standard. All digital monitors have an accuracy specification of 2%

Control Software:

A Windows graphical user interface example is provided

High Voltage Enable:

A hardware based, dry contact closure will enable the power supply into the high voltage on mode

Monitor Signals:

Voltage and current monitor signals are scaled 0-10Vdc equals 0-100% of full scale, accuracy is 1%

Over Power Fault:

 The maximum power the unit can supply can be programmed (0-1200 watts) via the digital interface, this setting will be stored in memory. An over power fault will occur if the output power is ≥ 105% of the set point value. When an over power fault occurs the high voltage output will be disabled and the Over Power Fault indictor will be activated on the GUI/Applet. Additionally both the UV and OV fault LED’s on the DXM100 will be illuminated.

Cooling:

Forced air

Dimensions:

6.25. H X 12. W X 15.5. D (158.75mm x 304.79mm x 393.7mm)

Weight:

43 pounds (19.5kg)

Input Line Connector:

IEC320 with EMI filter, 6´ (1.83 meter) cord set provided

Output Connector:

CA10 (R10). See table for pin out information

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive. UL/CUL recognized, File E227588. RoHS Compliant.

DXM100 ANALOG INTERFACE—J2 15 PIN MALE D CONNECTOR

RS-232 DIGITAL INTERFACE—J3 9 PIN FEMALE D CONNECTOR

USB DIGITAL INTERFACE—J4 4 PIN USB "B" CONNECTOR

ETHERNET DIGITAL INTERFACE—J5 8 PIN RJ45 CONNECTOR

J6 CA10 (R10) HV CONNECTOR

Note: No high voltage cable is provided

Tablas y Diagramas

DIMENSIONS: in.[mm]

BOTTOM VIEW

FRONT VIEW

SIDE VIEW