
SERIE PCM
- Voltaje de salida de 1 kV a 70 kV
- Baja energía almacenada
- Reconocimiento UL y cumplimiento CE
- Personalización disponible para OEM
FUENTES DE ALIMENTACIÓN DE ALTO VOLTAJE DE 120 W
La serie PCM de módulos de alimentación de alto voltaje de 120 W con entrada de CA de Spellman incorpora un extremo frontal con factor de potencia corregido, proporcionando 0.99 de factor de potencia además de una capacidad de voltaje de entrada universal (85 VCA a 265 VCA). Estos módulos de polaridad fija (que se especifican como positivos o negativos al momento de ordenarlos) cuentan con regulación de voltaje y corriente con cruce automático, haciéndolos ideales para aplicaciones de cargas sensibles. El diseño robusto de la serie PCM y su amplia protección contra arco y cortocircuito le permiten la operación en los ambientes más demandantes.
Aplicaciones típicas:
- Electrohilado
- Pruebas de potencial alto
- Arreglos de detectores
- Electroforesis
- Prueba de cables
Especificaciones
(Ref. 128006-001 REV. T)
Input:
85-265Vac, 47-63Hz @ 1.8A, power factor corrected.
UL® rated for 85-250Vac input for 1kV to 5kV models.
Power Factor (Typical):
FL: 0.99
NL: 0.98
Efficiency:
80 to 85%, typical
Output:
11 models from 1kV to 70kV. Positive or negative polarity outputs, specify at time of order.
Voltage Regulation:
Load: 0.01% of output voltage, no load to full load.
Line: ±0.01% for ±10% change in input voltage.
Current Regulation:
Load: 0.01% of output current from 0 to rated voltage. Line: 0.01% of rated current over specified input range.
Ripple:
0.1% p-p of maximum output voltage.
Voltage Stability:
0.02% per 8 hours.
Temperature Coefficient:
100ppm per °C, voltage or current regulated.
Environmental:
Operational: 0 to 40°C
Storage: -40°C to +85°C
Humidity: 0 to 90%, non-condensing
Dimensions:
1kV to 50kV: 3.65”H x 5”W x 9”D (9.27cm x 12.7cm x 22.9cm).
60, 70kV: 3.65”H x 5”W x 11”D (9.27cm x 12.7cm x 27.9cm).
Weight:
7 pounds (3.18kg)
AC Input Connectors:
IEC320 with mating cable.
Interface Connector:
15 pin D connector.
HV Output Cable:
Spellman Delrin type connector with 36” (91.4cm) shielded cable.
Front Panel Ground Connection:
Threaded 8-32 ground stud
Regulatory Approvals:
Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive. UL/CUL recognized, File E148969 (up to 60kV only). RoHS Compliant
PCM SELECTION TABLE
Maximum Rating | Model Number | |
---|---|---|
kV | mA | |
1 | 120 | PCM 1*120 |
3 | 40 | PCM 3*120 |
5 | 24 | PCM 5*120 |
10 | 12 | PCM 10*120 |
15 | 8 | PCM 15*120 |
20 | 6 | PCM 20*120 |
30 | 4 | PCM 30*120 |
40 | 3 | PCM 40*120 |
50 | 2.4 | PCM 50*120 |
60 | 2.0 | PCM 60*120 |
70 | 1.7 | PCM 70*120 |
*Specify “P” for positive polarity or “N” for negative polarity.
PCM D CONNECTOR 15 PIN
Pin | Signal | Parameters |
---|---|---|
1 | Remote mA Program | 0 to 10Vdc = 0 to 100% of rated output |
2 | Remote kV Program | 0 to 10Vdc = 0 to 100% of rated output |
3 | High Voltage Enable/Inhibit | Open = HV Inhibit, Ground = HV ON |
4 | mA Monitor | 0 to 10Vdc = 0 to 100% of rated output |
5 | Interlock Return | Connect to pin 6 to close interlock circuit |
6 | Interlock Out | Connect to pin 5 to close interlock circuit |
7 | kV Monitor | 0 to 10Vdc = 0 to 100% of rated output |
8 | Local kV Program | Multi-turn front panel pot (screwdriver) |
9 | Power Supply Fault | 0Vdc = No Fault, +15Vdc @ 1mA = Fault |
10 | +10Vdc Reference | +10Vdc @ 1mA maximum |
11 | Signal Ground | Signal Ground |
12 | Spare | No Connection |
13 | Spare | No Connection |
14 | Spare | No Connection |
15 | Local mA Program | Multi-turn front panel pot (screwdriver) |
Tablas y Diagramas
DIMENSIONS: in.[mm]
SIDE VIEW
TOP VIEW
BACK VIEW
Frequently Asked Questions
What Is a Safe Level of High Voltage?
Where Can I Obtain Information on High Voltage Safety Practices?
What Kind of High Voltage Connector Do You Use on Your Supplies?
What Do You Mean That the Output Side of the High Voltage Cable on Most Standard Products Is “Unterminated”?
How Should I Ground Your Supply?
Why Is Arcing an Issue for a High Voltage Power Supply?
Application Notes AN-19 – High Voltage Cable Lengths Discussed