XRB160PN192 Monoblock® Industrial X-Ray Generators
- Integrated HV Supply, Filament Supply, X-Ray Tube, Beam Port and Control Electronics
- Compact & Lightweight
- Universal Input, Power Factor Corrected
- Can be Mounted in Any Physical Orientation
- Analog Monitoring and Standard RS-232 Digital Interface
*Note: All specifications are subject to change without notice. Please consult the English PDF version of this datasheet for the most up-to-date revision.
160kV, 200W X-Ray Source
Spellman’s XRB160PN192 Monoblock® X-Ray source is designed for OEM applications powering its internal X-Ray tube up to 160kV at 192W. Features like universal input, small package size and a standard analog and RS-232 digital interface simplify integrating this Monoblock® into your X-Ray system. Standard models are available with fan shaped beam geometry. Proprietary emission control circuitry provides excellent regulation of X-Ray tube current, along with outstanding stability performance.
- X-Ray Scanning: Plating Measurement
- Food Inspection
- Fill Level Confirmation
- Security Applications
(Ref. 128082-001 REV. L)
Tube Type: Glass tube, Tungsten target, Be filter
Focal Spot: 0.8mm x 0.8mm.
Beam Filter: 0.016. thick 6061 Al.
Beam Geometry: Asymmetrical fan 80° x 10° +/-2°
100-240Vac, 50/60Hz, 5A maximum +/-10%
X-Ray Tube Voltage:
Nominal X-Ray tube voltage is adjustable between 80kV to 160kV
X-Ray Tube Current:
0.1mA to 1.2mA, 192W maximum over specified tube voltage range
X-Ray Tube Power:
192W, maximum continuous
Line: ±0.1% for a ±10% input line change of nominal input line voltage Load: ±0.1% for a 0.1mA to 1.2mA load change
Voltage measured across the X-Ray tube is within ±2% of the programmed value
Ramp time shall be <200ms from 10% to 90% of rated output
Within 5% of rated voltage in <10ms
1% p p of rated voltage @ =1kHz
Line: ±0.1% for a ±10% input line change of nominal input line voltage
Load: 0.5% @ 80-160kV, 0.1mA to 1.2mA
Current measured through the X-Ray tube is within ±2% of the programmed value
<200ms from 10% to 90% of rated output
4 arcs in 10 seconds with a 200ms quench = Shutdown
Internal high frequency AC filament drive with closed loop filament emission control
0 to 10Vdc ground referenced signals
A demo GUI for engineering evaluations will be provided for the RS-232 digital interface upon request.
A hardware interlock function is provided
0°C to +40°C
-40°C to +70°C
10% to 95% relative humidity, non-condensing
Natural convection augmented by customer provided 250cfm cooling fans for 200W operation
Input Line Connector:
6 pin Molex 26-60-4060
Analog Interface Connector:
7 pin Molex 26-60-5070
Digital Interface Connector:
9 pin D connector, female
32 ground stud provided on chassis
18" X 13.5" X 7.63" (458mm X 343mm X 193.80mm)
Can be mounted in any orientation.
Not to be greater than 0.5mR/hr at 5cm outside the external surface.
Compliant to EEC EMC Directive (External EMC filter required). Compliant to EEC Low Voltage Directive. UL/CUL recognized file E235530.
AC INPUT POWER J1 6 PIN CONNECTOR
RS-232 DIGITAL INTERFACE— JB16 9 PIN FEMALE D CONNECTOR
ANALOG INTERFACE— J7 7 PIN MOLEX CONNECTOR
|1||Ex Gate||Low = X-Ray OFF, +12Vdc = X-Ray ON|
|4||kV Monitor||0-9 Vdc = 0 to 100% rated output|
|6||mA Monitor||0 to 9Vdc = 0 to 100% rated output|
|7||Fault||Open collector, 35V @ 10mA max, High = No Fault|
|Indicator||Signal Name||Condition Illuminated When...|
|LED 1||OV||High kV occurs|
|LED 2||UV||Low kV occurs|
|LED 3||UC||Low mA occurs|
|LED 4||OC||High mA occurs|
|LED 5||ARC FLT||Arc fault occurs|
|LED 6||OT||Over temperature occurs|
|LED 7||X-RAY ON||X-Rays are enabled|
|LED 8||PWR||Power is ON|
테이블 및 다이어그램
Frequently Asked Questions
Why Is Oil Insulation Used?
Do I Need to Ensure My Monoblock® Stays Cool? Why?
How Often Do I Need to Season My Monoblock® X-Ray Source? Why?
Application Notes AN-12 – The Benefit of Using a Current Source to Power X-Ray Tube Filament Circuits