XRV СЕРИЯ
- Модели 160 кВ, 225 кВ, 320 кВ, 350 кВ и 450 кВ
- Полнофункциональный рентгеновский генераторe
- Электронные схемы подачи переменного тока с коррекцией коэффициента мощности
- Интегрированный сдвоенный источник питания накала
- Цифровые интерфейсы USB, Ethernet и RS-232
- Превосходная стабильность и регулировка
- Доступен в корпусе с черным порошковым покрытием
* Примечание: Все спецификации могут быть изменены без предварительного уведомления. Пожалуйста, ознакомьтесь с английской версией PDF этой спецификации для получения последней актуальной информации об оборудовании.
1.8 - 6kW Промышленные рентгеновские генераторы
Высоковольтные источники питания Spellman серии XRV — новый стандарт для компактных и высокопроизводительных рентгеновских генераторов мощностью от 1,8 до 6,0 кВт. Доступны модели с выходным напряжением в диапазоне от 160 кВ до 450 кВ с различной полярностью (отрицательная, положительная, биполярная), что позволяет подобрать модель практически для любой сферы применения.
Схема активной коррекции коэффициента мощности позволяет снизить требования к качеству входного питания и сводит к минимуму влияние помех в питающей сети. Запатентованная компанией Spellman топология инвертора позволяет создавать блоки питания с беспрецедентно высокими КПД и плотностью мощности. Зона высокого напряжения с твердотельной изоляцией позволяет дополнительно уменьшить размеры устройства и обеспечивает надежную работу, снижая частоту технического обслуживания.
Электронные схемы, созданные с использованием технологии поверхностного монтажа, обеспечивают поддержку интерфейсов USB, Ethernet и RS232, а также аналоговых интерфейсов, что упрощает интеграцию в системы заказчиков. Два выхода постоянного тока, источники питания накала, управляемые посредством высокотехнологичной схемы стабилизации тока эмиссии, позволяют обеспечить точность сигналов и стабильность токов в рентгеновской трубке. В этот компактный рентгеновский генератор встроены электронные схемы комплексной диагностики сбоев, а также функции отслеживания дуги, гашения дуги и подсчета количества отключений по дуге.
Технические характеристики
(Ref. 128060-001 REV. AE)
Typical Applications
Non Destructive TestingX-Ray Scanning
Security Applications
Medical Applications
Options
400Vac ±10% (6kW only)
GUI Control Software for XRV
XRVC (XRV Controller)
Specifications
Input Voltage:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
180-264Vac, single phase, 47-63 Hertz, active power factor corrected input to ≥0.98
6.0kW models:
208 or 400Vac, ±10%, three phase, 47-63 Hertz, passive power factor corrected
Input Current:
1.8kW, 3.0kW, 4.0kW and 4.5kW models: <30 amps
6.0kW models: <25 amps per phase
Output Voltage:
Accuracy: 0.25%
Stability: ≤ 0.1% per 8 hours, after 1 hour warm up
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Load:±0.05% of rated output voltage for a full load change
Line: ±0.05% of rated output voltage over specified input voltage range
6.0kW models:
Load:±0.1% of rated output voltage for a full load change
Line: ±0.1% of rated output voltage over specified input voltage range
Output Polarity:
See “model selection” table
Output Current:
See “model selection” table
Ripple:
See “model selection” table
Temperature Coefficient:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
50ppm/°C
6.0kW models:
±50ppm/°C
Emission Current:
Accuracy: 0.25%
Stability: 100ppm/°C
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Load: ±0.05% of rated output current for a change from 30% to 100% of rated output voltage
Line: ±0.05% of rated output current over specified input voltage range
6.0kW models:
Load: ±0.1% of rated output current for a change from 30% to 100% of rated output voltage
Line: ±0.1% of rated output current over specified input voltage range
Filament:
Output:
0-6 amps at a compliance of 10Vdc, maximum
Dual Focal Spot:
Small and large, selectable via interface signal
Configuration:
DC filament drive. Closed loop emission control regulates filament setting to provide desired X-Ray tube emission current
Control Interface:
Remote Interface:
Analog, USB, Ethernet and RS-232 are standard
Control Software:
A Windows graphical user interface example is provided.
Environmental
Temperature Range:
Operating: 0°C to +50°C
Storage: -40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Mains Input Connector:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Type 97-3102A-24-11P
6.0kW models:
Type 97-3102A-24-22P
Interface Connectors:
Digital—Ethernet, RS-232 and USB
Analog—25 pin connector
Output Connector:
See “model selection” table
Cooling:
Forced air
Regulatory Approvals:
Compliant to EEC EMC Directive/Compliant to EEC Low Voltage Directive. File E227588. RoHS Compliant.
XRV160/320/350 SPECIFICATIONS
| XRV160*1800 | XRV160*3000 | XRV160*4000 | XRV160*6000 | XRV320P&N1800 | XRV320P&N4500 | XRV350P&N4500 | |
|---|---|---|---|---|---|---|---|
| DC Output Voltage | 5kV to 160kV | 5kV to 160kV | 5kV to 160kV | 5kV to 160kV | 5kV to ±160kV | 5kV to ±160kV | 5kV to ±175kV |
| Polarity* | Pos or Neg | Pos or Neg | Pos or Neg | Pos or Neg | Bipolar | Bipolar | Bipolar |
| Output Rated Current | 0-30mA | 0-30mA | 0-50mA | 0-50mA | 0-30mA | 0-30mA | 0-30mA |
| Output Power | 1.8kW | 3.0kW | 4.0kW | 6.0kW | 1.8kW | 4.5kW | 4.5kW |
| Ripple/Noise (p-p) | <0.025% | <0.05% | <0.1% | <0.25% | <0.025% | <0.1% | <0.1% |
| Dimensions | 10.09˝ H x 17.16˝ W x 24˝ D (256mm x 436mm x 609mm) | 2 x (10.09˝ H x 17.16˝ W x 24˝ D) (256mm x 436mm x 609mm) | |||||
| Weight | 150 lbs. (68kg) | 150 lbs. (68kg) | 150 lbs. (68kg) | 155 lbs. (70.3kg) | 300 lbs. (136 kg) | 300 lbs. (136 kg) | 300 lbs. (136 kg) |
| Output Connector | R24 | R24 | R24 | R24 | Two R24 | Two R24 | Two R24 |
XRV225/450 SPECIFICATIONS
| XRV225*1800 | XRV225*3000 | XRV225*4000 | XRV225*6000 | XRV450P&N1800 | XRV450P&N4500 | |
|---|---|---|---|---|---|---|
| DC Output Voltage | 5kV to 225kV | 5kV to 225kV | 5kV to 225kV | 5kV to 225kV | 5kV to ±225kV | 5kV to ±225kV |
| Polarity* | Pos or Neg | Pos or Neg | Pos or Neg | Pos or Neg | Bipolar | Bipolar |
| Output Rated Current | 0-30mA | 0-30mA | 0-30mA | 0-30mA | 0-30mA | 0-30mA |
| Output Power | 1.8kW | 3.0kW | 4.0kW | 6.0kW | 1.8kW | 4.5kW |
| Ripple/Noise (p-p) | <0.025% | <0.05% | <0.1% | <0.25% | <0.025% | <0.1% |
| Dimensions | 15.90˝ H x 17˝ W x 30.72˝ D (404mm x 432mm x 780mm) | 2 x (15.90˝ H x 17˝ W x 30.72˝ D) (404mm x 432mm x 780mm) | ||||
| Weight | 240 lbs. (109kg) | 240 lbs. (109kg) | 240 lbs. (109kg) | 480 lbs. (218 kg) | 480 lbs. (218 kg) | |
| Output Connector | R28** | R28** | R28** | Two R28** | Two R28** | |
Units are available in positive output polarity without filament, see model selection table for ordering details.
*Specify “P” for positive or “N” for negative polarity.
**Order SHV HV cable flange p/n 407141-024 if using Comet HV cable with R28SL spring loaded plug.
| Pin | Signal | Parameters |
|---|---|---|
| C | HV Output | XRV160 and XRV320—R24 Connector XRV225 and XRV450—R28 Connector |
| S | Small Filament Output | 0 to 6 amps @ 10Vdc |
| L | Large Filament Output | 0 to 6 amps @ 10Vdc |
J2 ANALOG INTERFACE—25 PIN D CONNECTOR
| Pin | Signal | Parameters |
|---|---|---|
| 1 | Power Supply Fault | Low, sum of faults, HVPS detected a fault, open collector, 50V @ 10mA max |
| 2 | mA Program | 0 to 10V FS Z in = 10M ohms |
| 3 | kV Program | 0 to 10V FS Z in = 10M ohms |
| 4 | Filament Limit L/S Ref.* | 0 to 10V FS Z in = 10M ohms |
| 5 | Filament Preheat L/S Ref.* | 0 to 10V FS Z in = 10M ohms |
| 6 | kV Monitor | 0 to 10V FS Z out = 4.99k ohms |
| 7 | mA Monitor | 0 to 10V FS Z out = 4.99k ohms |
| 8 | Filament Current Monitor* | 0 to 10V FS Z out = 4.99k ohms |
| 9 | Signal Ground | Ground |
| 10 | X-Ray Enable | +24Vdc = X-Ray ON, connect to pin 14 with dry contact relay |
| 11 | Filament ON* | Filament ON status, low, filament is ON open collector 50V, @ 10mA max |
| 12 | Interlock 1 | Active low, interlock is closed, safe to enable HV |
| 13 | Interlock 2 | Active low, interlock is closed, safe to enable HV |
| 14 | +24Vdc | +24Vdc @ 100mA, maximum |
| 15 | Filament Enable* | Active low, turn filament ON |
| 16 | Filament Control* | Active low, filament is regulated by ECR (HV must be ON). Not active, the filament is regulated by the preheat reference |
| 17 | Filament L/S Select | Filament selection large or small, low = small spot is selected |
| 18 | Filament L/S Confirm | Open collector, 50V @ 10mA max Filament selection confirm, low = small spot is selected |
| 19 | HVPS RDY | Low = HVPS ready, open collector, 50V @ 10mA max |
| 20 | X-Ray ON | X-Ray ON status, low = X-Rays are ON open collector, 50V @ 10mA max |
| 21 | Interlock Status | Low, interlocks are closed, can enable HV open collector, 50V @ 10mA max |
| 22 | GND | Digital ground |
| 23 | X-Ray ON Pre-Warn | Pre-warning, low, before X-Ray ON open collector, 50V @ 10mA max |
| 24 | Reset | Active low, minimum 10mS transition |
| 25 | Arc fault | Low, arc fault, the HVPS has detected an arc open collector, 50V @ 10mA max |
*Not active on positive models
MODEL SELECTION TABLE
| Model | Voltage | Power | Polarity |
|---|---|---|---|
| XRV160*1800 | 160kV | 1.8kW | Pos or Neg |
| XRV160*3000 | 160kV | 3.0kW | Pos or Neg |
| XRV160*4000 | 160kV | 4.0kW | Pos or Neg |
| XRV160*6000/208V | 160kV | 6.0kW | Pos or Neg |
| XRV160*6000/400V | 160kV | 6.0kW | Pos or Neg |
| XRV225*1800 | 225kV | 1.8kW | Pos or Neg |
| XRV225*3000 | 225kV | 3.0kW | Pos or Neg |
| XRV225*4000 | 225kV | 4.0kW | Pos or Neg |
| XRV225*6000/208V | 225kV | 6.0kW | Pos or Neg |
| XRV225*6000/400V | 225kV | 6.0kW | Pos or Neg |
| XRV320P&N1800 | ±160kV | 1.8kW | Bipolar |
| XRV320P&N4500 | ±160kV | 4.5kW | Bipolar |
| XRV350P&N4500 | ±175kV | 4.5kW | Bipolar |
| XRV450P&N1800 | ±225kV | 1.8kW | Bipolar |
| XRV450P&N4500 | ±225kV | 4.5kW | Bipolar |
*Specify “P” for positive or “N” for negative polarity. Positive polarity models do not have
integrated filament power supplies. Contact Spellman for custom output voltage/power models.
RS-232 DIGITAL INTERFACE—J3 9 PIN FEMALE D CONNECTOR
| Pin | Signal | Parameters |
|---|---|---|
| 1 | N/C | No Connection |
| 2 | TX out | Receive Data |
| 3 | RX in | Transmit Data |
| 4 | N/C | No Connection |
| 5 | SGND | Ground |
| 6 | N/C | No Connection |
| 7 | N/C | No Connection |
| 8 | N/C | No Connection |
| 9 | N/C | No Connection |
ETHERNET DIGITAL INTERFACE—J4 8 PIN RJ45 CONNECTOR
| Pin | Signal | Parameters |
|---|---|---|
| 1 | VBUS | +5 Vdc |
| 2 | D- | Data - |
| 3 | D+ | Data + |
| 4 | GND | Ground |
JB1 MAIN AND AUXILIARY INPUT POWER—TYPE 97-3102A-24-11P (Single Phase Units)
| Pin | Signal | Parameters |
|---|---|---|
| A | Auxiliary AC Line Power | 180-264Vac |
| B | Auxiliary Ground | Ground |
| C | Auxiliary AC Neutral | Neutral |
| D | Main AC Line Power | 180-264Vac |
| E | Main Ground | Ground |
| F | Main AC Neutral | Neutral |
JB1 MAIN AC INPUT POWER—TYPE 97-3102A-24-22P (Three Phase Units)
| Pin | Signal | Parameters |
|---|---|---|
| A | Line 1 | 208Vac, ±10%, 50/60Hz @ 25 amps |
| B | Line 2 | 208Vac, ±10%, 50/60Hz @ 25 amps |
| C | Line 3 | 208Vac, ±10%, 50/60Hz @ 25 amps |
| D | GND | Ground |
Note: Use 4 conductor cable or single isolated wires rated no
less that 600Vac, 30 amps (10AWG, minimum)
JB2 AUXILIARY AC INPUT POWER—TYPE 97-3102A-20-3P (Three Phase Units)
| Pin | Signal | Parameters |
|---|---|---|
| A | Line 1 | 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2) |
| B | Line 2 | 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2) |
| C | GND | Ground |
System Ground: System ground wires (10AWG minimum) to
the ground terminal E1 GND to the power supply using ground
stud M6 X 20MM, with M6 nut.
Таблицы и диаграммы
DIMENSIONS: in.[mm]
XRV160
TOP VIEW
FRONT VIEW
REAR VIEW
XRV225
TOP VIEW
FRONT VIEW
REAR VIEW
Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.
