230 シリーズ

  • モジュラー卓上型デザイン
  • 低リップルおよびノイズ
  • 3.5桁フロント・パネル・デジタル・メータ
  • 両極性出力

ベンチトップ 高圧電源

Bertanブランド230シリーズ高圧電源装置は安定した、1〜 30kVまでの高圧出力が得られます。低ノイズでリニア・トポロ ジ採用の本装置では極めて低い出力リップル仕様が得られます。 これら12〜15Wのユニットはその設計から本来両極性で、正負 極いずれもの出力極性を備えています。本230シリーズ装置に はアークおよび短絡から完全に保護される設計になっています。 優れたレギュレーション仕様が同じく優れた安定性とともに本装 置の特徴です。

用途

  • ハイポット試験
  • 静電気使用装置
  • 一般ラボ用

CE Marking

Specifications

(Ref. 128051-001 REV. J)

Input Voltage:

115Vac, ±10%, 50/60Hz @ 0.5A 

230Vac, ±10%, 50/60Hz @ 0.25A 

Input voltage is switch selectable

Output Voltage:

See “model selection” table

Output Polarity:

All units are reversible polarity by design

Output Current:

See “model selection” table

Voltage Regulation:

Line: ±0.002% of rated output voltage over specified input voltage range

Load:±0.005% of rated output voltage for a full load change

Current Regulation:

Internally set to limit at less than 125% of rated current. 

A rear panel switch allows limiting at 25% of rated full current.

Ripple:

See “model selection” table 

Temperature Coefficient: =100ppm/°C

Stability:

≤ 0.01%/hour, 0.02% per 8 hours after a 1/2 hour warm up

Accuracy:

Front panel control: ±(0.2% of setting + 0.2% of maximum)

Front panel Meter: Voltage ±(0.5% of setting + 0.5% of maximum), Current  ±(2% of setting + 0.5% of maximum)

Remote Programming: ±(0.1% of setting + 0.1% of maximum)

Voltage Monitor: ±(0.1% of reading + 0.1% of maximum)

Current Monitor: ±(2% of reading + 1% of maximum)

 Front Panel Metering and Controls:

 Power ON/OFF switch

 3.5 digit metering for voltage and current, switch selectable

Polarity indicator

10 turn locking potentiometer to set output voltage

HV output connector

Ground stud

Operating Temperature

 0°C to +50°C

 Storage Temperature:

 -40°C to +85°C

 Humidity:

 20% to 85% RH, non-condensing

 Input Line Connector:

 IEC320 EMI filter/input connector, a detachable line cord is provided 

Interface Connector: 

9 pin “D” connector, a mating connector is provided

Output Connector:

A detachable 10 foot (3 meter) HV cable is provided for units up to 5kV;

10kV through 20kV: 59” (1.5 meter); 30kV: 10 foot (3 meter)

 Cooling:

 Convection cooled

 Dimensions

 7.63. W X 5.03. H X 8.91. D

 (194mm X 128mm X 226mm)

Weight:

≤ 10lbs (4.5kg)

Regulatory Approvals:

 Compliant to 2004/108/EC, the EMC Directive and 

 2006/95/EC, the Low Voltage Directive.

OPTIONS

F - Isolated (Floating) Output

MODEL SELECTION TABLE

230 Voltage Current Ripple Series
230-01R 0 to 1kV 0 to 15mA 10mV
230-03R 0 to 3kV 0 to 5mA 30mV
230-05R 0 to 5kV 0 to 3mA 50mV
230-10R 0 to 10kV 0 to 1.5mA 500mV
230-20R 0 to 20kV 0 to 0.5mA 2V
230-30R 0 to 30kV 0 to 0.4mA 5V

INTERFACE CONNECTOR

Pin Signal Parameters
1 Voltage Monitor 0 to 5Vdc = 0 to 100% rated voltage, Zout = 10KΩ SIDE VIEW
2 N/C No Connection
3 Enable TTL "0" disables HV, TTL "1" or open enables HV
4 +5Vdc Reference +5.0Vdc @ 10mA, maximum
5 Current Monitor 0 to 5Vdc = 0 to 100% rated current, Zout = 10KΩ
6 Voltage Program Input 0 to 5Vdc = 0 to 100% rated voltage, Zin = 1MΩ
7 Analog Ground Ground
8 Digital Ground Ground
9 Polarity Indicator Open collector, 30V @ 25mA, positive = ON

OPTIONS:

Isolated (Floating) Output-Option F 

Units up to and including 5kV can be provided with differential outputs capable of floating up to ±2kV from ground. Voltage programming and monitoring functions are normally referenced to ground. Current monitor­ing and metering is eliminated. Replace “R” suffix with “F” for this option. Output connectors (positive, negative and ground) for 1kV and 3kV models are 3-way binding posts; 5kV model uses Spellman P/N JAC for positive and negative outputs with 3-way binding post for ground. Mating connectors are Spellman P/N PA (MHV type 1705-14)

Tables & Diagrams

DIMENSIONS: in.[mm] 

FRONT VIEW

230シリーズ ベンチトップ 高圧電源 (Image 1)

SIDE VIEW

230シリーズ ベンチトップ 高圧電源 (Image 2) 

BACK VIEW

230シリーズ ベンチトップ 高圧電源 (Image 3)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.