XRB180PN200

スペルマンのXRB180PN200は、最大180kV、200Wで動作する一体型X線源で、OEMユーザに重要な検査やスクリーニング・アプリケーション用のコンパクトなプラグアンドプレイMonoblockを提供します。25°の角度を持つ固定陽極X線管を搭載し、80°x 4°のファンビームを提供します。独自のエミッション制御回路により、X線管電流の優れた制御を実現し、業界をリードする線量安定性と画質を提供します。このコンパクトなモデルには、標準的なアナログとRS-232デジタル制御が付属しています。このプラットフォームは、特定のOEMシステム要件に合わせてカスタマイズすることができます。

代表的なアプリケーション

航空保安検査：受託手荷物/EDS、検問所車両検査、一般NDT、食品検査

Specifications

^{(Ref. 128085-001 REV. A)}

X-Ray Characteristics:

Tube Type:  Stationary Anode, tungsten target

Focal Spot:  0.8 x 0.8mm nominal (IEC60336)

Beam Filter:  Consists of oil and the curved Ultem 0.079'' +/-0.01''. Inherent filtration in the X-Ray Tube is 1mm Be, 1.5mm +/-10% glass.

Beam Geometry: Fan of 80° X 4°, ±1%

Anode Angle: 25°

Input Voltage:

Power factor corrected input to 0.98. 100Vac to 240Vac, ±10%, 50/60 Hertz. 5A, maximum

X-Ray Tube Voltage:

Nominal X-Ray tube voltage is adjustable between 90kV to 180kV.

Voltage Accuracy:

The high voltage measured at the X-ray tube will be within ±1% of the selected value.

Voltage Ripple:

Ripple will be ≤0.2% of maximum rated voltage for frequencies ≤1kHz

Voltage Regulation:

< ±0.1% for ±10% of nominal input line change
< ±0.1% for 0.5mA to 1.11mA load change

Voltage Overshoot:

kV overshoot will return within 5% of full voltage in less than 10ms

Risetime:

The voltage and current risetime is controlled by a ramping circuit. Ramp time is less than 0.5 second from 10% to 90% of output voltage and current.

X-Ray Tube Current:

0.5mA to 1.1mA @ 180kV, 200 Watts maximum

Current Accuracy:

<±1% of the selected value.

Current Regulation:

<0.5% at 90-180kV, 0.5mA to 1.1mA

Arc Intervention:

Unit will detect a single arc but HV will not shut down. If multiple arcs occur (4 in 10 seconds) then the unit will shut down.

Filament Configuration:

Internal high frequency AC filament drive operated in current mode with closed loop filament emission control.

Analog Interface:

Ground referenced 0 to 10Vdc for all monitoring signals. Relay contacts and open collector outputs for other signals.

Digital Interface:

Internal high frequency AC filament drive with closed loop filament emission control

Digital Interface:

The RS-232 interface allows for programming of the voltage, current, and X-Ray Enable. Provides monitoring for voltage, current and oil temperature. Tolerance is 3% (with additional 5uA offset at ≤10%mA programming)

Control Software:

A demo GUI is available for engineering evaluation

Operating Temperature:

0°C to +40°C

Storage Temperature:

-40°C to +70°C

Humidity:

10% to 95% relative humidity, non-condensing.

Cooling:

Via natural convection/external cooling fans of 100CFM minimum or maintaining tank/oil temperature below 55°C

Input Line Connector:

3 pin Phoenix Contact, p/n 1829167. Mating connector provided with unit.

Analog Interface Connector:

10 pin Phoenix Contact, p/n 1755503. Mating connector provided with unit.

Digital Interface Connector:

9 pin female D connector. Mating connector provided with unit.

Grounding Point:

M4 grounding stud provided on chassis.

Dimensions:

See outline drawing.

Weight:

132 pounds (60kg).

Orientation:

Can be mounted in any orientation.

X-Ray Leakage:

Not to be greater than .5mR/hr at 5cm from any surface of the Monoblock® when measured at 180kV @ 1.1mA

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive.

AC INPUT POWER 3 PIN P/N 1829167

ANALOG INTERFACE— 10 PIN PHOENIX CONTACT P/N 1755503

RS-232 DIGITAL INTERFACE— 9 PIN MALE D CONNECTOR

FRONT PANEL LED INDICATORS

Tables & Diagrams

 DIMENSIONS: in.[mm

TOP VIEW

SIDE VIEW

BACK VIEW

FRONT VIEW