XRB502 Monoblock® 工业X射线发生器 (featured)

XRB160PN480/2 Monoblock® 工业X射线发生器

  • 集成高压电源,灯丝电源,X 射线管,电子束端口和控制电子设备
  • 紧凑,轻便
  • 通用输入,功率因数校正
  • 可以安装在任何物理方向
  • 模拟控制接口和标准 RS-232 数字接口

*注意:所有规格如有变更,恕不另行通知。有关最新修订,请参阅本数据表的英文 PDF 版本

160kV,480W X 射线源

  斯派曼 XRB160PN480/2 系列 Monoblock® X 射线源是专为 OEM 应用而设计。输出电压为 160kV,功率为 500W,为内部的 X 射线管供电。产品具有通用的电源输入、小的外观尺寸、标准的模拟接口和 RS-232 数字接口等特点,使得此Monoblock® 能更简单集成到您的 X 射线系统中。标准的型号是扇形射线束。专有的发射控制电路提供了卓越的 X 射线管电流管理,同时具有出色的稳定性和性能。


  • X 射线扫描:食品检验、液位确认和安检应用
CE Marking


(Ref. 128087-001 REV. J)

X-Ray Characteristics:

Tube Type: Glass tube, Tungsten target, Be filter

Focal Spot: 0.8mm x 0.8mm (IEC336)

Beam Filter: 1mm curved window

Beam Geometry: Asymmetrical fan 80° x 10° ±2°

Input Voltage:

100-240Vac ±10%, 50/60Hz, 6.5A max; 12Vdc @ 5A

X-Ray Tube Voltage:

Nominal X-Ray tube voltage is adjustable between 80kV to 160kV

X-Ray Tube Current: 

0.25mA to 3mA over specified tube voltage range

X-Ray Tube Power:

500W, maximum

Voltage Regulation:

Line: ±0.1% for a ±10% input line change of nominal input line voltage

Load: ±0.1% for a 0.3mA to 3mA load change

Voltage Accuracy:

Voltage measured across the X-Ray tube is within ±1% of the programmed value

Voltage Risetime:

Ramp time shall be <1 second from 10% to 90% of rated output 

Voltage Overshoot:

Within 5% of rated voltage in <10ms

Voltage Ripple:

0.1% p p of rated voltage @ ≤1kHz

Current Regulation:

Line: ±0.1% for a ±10% input line change of nominal input line voltage

Load: ±0.5% @ 80-160kV, 0.3mA to 3mA

Current Accuracy:

Current measured through the X-Ray tube is within ±1% of the programmed value

Current Risetime:

<1 second from 10% to 90% of rated output 

Arc Intervention:

4 arcs in 10 seconds with a 200ms quench = Shutdown

Filament Configuration:

Internal high frequency AC filament drive with closed loop filament emission control

Analog Interface:

0 to 10Vdc ground referenced signals

Digital Interface:

RS-232 interface.

Control Software:

A demo GUI for engineering evaluations will be provided for the RS-232 digital interface upon request.

Interlock Signals:

A hardware interlock functions in both analog and digital programming modes.

Operating Temperature:

0°C to +40°C

Storage Temperature:

-40°C to +70°C


95% relative humidity, non-condensing


Heat exchanger w/fan and oil pump, powered from DC input;

Input Line Connector:

3 pin, Phoenix Contact 1829167

Analog Interface Connector:

10 pin, Phoenix Contact 1755503

Digital Interface Connector:

9 pin D connector, female

Grounding Point:

8-32 ground stud provided on chassis


See outline drawing


125lbs (56.7kg)


Can be mounted in any orientation.

X-Ray Leakage:

Not to be greater than 0.5mR/hr at 5cm outside the external surface.


Pin Signal Parameters
1 Line Line
2 Ground Ground
3 Neutral Neutral


Pin Signal Parameters
1 X-Ray Signal +24Vdc =Enable X-Ray, 0Vdc/open = Disable X-Ray,
2 X-Ray Signal Return Signal Return
3 N/C N/C
4 kV Monitor 0-10Vdc = 0 to 178kV, Zout = 10kΩ
5 Signal Ground Signal Ground
6 mA Monitor 0-10Vdc = 0 to 3.4mA, Zout = 10kΩ
7 Fault Signal Open collector, High (Open) = No Fault, 35Vdc
@10mA maximum
8 HV ON Lamp Relay n/o Relay Normally Open, 50Vdc @ 1A maximum
9 HV ON Lamp Relay common Relay Common, 50Vdc @ 1A maximum
10 HV ON Lamp Relay n/c Relay Normally Closed ,50Vdc @ 1A maximum


Indicator Signal Name Condition Illuminated When...
LED 1 OT Over temperature occurs
LED 2 ARC FLT Arc fault occurs
LED 3 UV Low kV occurs
LED 4 OV High kV occurs
LED 5 UC Low mA occurs
LED 6 OC High mA occurs
LED 7 X-RAY ON X-Rays are enabled
LED 8 PWR Power is ON