V6 系列

  • 紧凑式型号,电压高达 30kV
  • 高度稳定,低波纹,低噪音
  • 本地和远程设定及监控
  • RoHS 合规

*注意:所有规格如有变更,恕不另行通知。有关最新修订,请参阅本数据表的英文 PDF 版本

 两年延保标志 CE RU 标识 RoHs 合规标志

紧凑型 30W 精密高压电源

V6 系列是可调节的/固定输出极性模块化的高压电源家族一员,在许多应用中提供非同一般的性能和价值。V6 系列电源采用全封装,专用于系统或工作台操作。输出电压的范围宽,一直到30kV 可供使用。通过内部多圈电位器,本地控制输出电压。所有型号均具有远程模拟电压或电流编程能力。模拟监测输出包括高压和电流输出的远程监测。

典型应用:

  • 光谱
  • CRT 测试
  • 探测器
  • 电子束系统
  • 一般实验室使用

ROHS Marking

规格

(Ref. 128069-001 REV. K)

Input Voltage:

AC Model: 100-240Vac, ±10%; 50/60 Hertz; 1 amp 
DC Model: 24Vdc ±10%, 2 Amps

Voltage Regulation:

Line: ±0.005% of maximum 90-240Vac input line change.
±0.005% of maximum ±10%Vdc input line change Load: ±0.01% of maximum for 0 to maximum rated output current change

Current Regulation:

Line: ±0.05% of maximum current for 90-240Vac input line change.
0.05% of maximum current for ±10% Vdc input change Load: 0.2% of maximum current for 0 to maximum rated output voltage change

Ripple:

See “model selection” table

Temperature Coefficient:

≤ 50ppm/°C

Stability:

≤ 0.01%/hour, 0.02% per 8 hours after a 1/2 hour warm up

Operating Temperature:

0°C to +50°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85%RH, non-condensing 

Local Control:

Internal multi-turn potentiometer for 0 to maximum output voltage (±0.2%)

Remote Programming:

0 to +5Vdc analog input signal proportional to 0 to maxi­mum rated output. Accuracy is ±(0.1% of setting +0.1% of maximum). The programming input impedance is 20 megohms. 

Voltage Monitor:

0 to +5V proportional to 0 to maximum output voltage. Accuracy is ±(0.1% of reading +0.1% of maximum).  The monitor impedance is 10 kilohms.

Current Monitor:

0 to +5V proportional to 0 to maximum output voltage. Accuracy is ±(2.0% of reading +1.0% of maximum).  The monitor impedance is 10 kilohms.

Enable:

Remote interlock enables (low) disables internally (high) the high voltage output. Signal is normally high and supply will default to a disabled condition.

Current Limit:

All units provide short circuit current limiting to less than 110% of the maximum rated output current. Supply is self restoring upon removal of cause limit condition. 

Arc/Short Circuit:

Short circuit and arc protected; self restoring.

Cooling:

Convection cooled

Output Connector: 

Models up to and including 5kV use a Spellman P/N JAC high voltage connector.  The required mating connector is a Spellman P/N 105808-384, which is provided. The 10kV through 30kV units use a Spellman P/N JGP high volt­age connector (Alden 8101). All 10 through 30kV units are 1 provided with mating connectors assembled to 2.0 meters 2 of high voltage cable.

Dimensions:

AC Model: 3.05. W X 5.1. H X 7.06. D (77mm X 132mm X 179mm)

DC Model: 2.32. W X 5.1. H X 7.06. D (59mm X 132mm X 179mm)

Weight:

AC Model: 4.5 pounds (2.0kg)

DC Model: 3.75 pounds (1.7kg)

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive. UL/CUL recognized, File E227588. RoHS Compliant.

OPTIONS

RS - RS-232 Interface

V6A MODEL SELECTION TABLE

V6 AC Series Voltage Current Ripple
V6A1*30 0 to 1kV 0 to 30mA 75mV
V6A1.5*30 0 to 1.5kV 0 to 20mA 75mV
V6A3*30 0 to 3kV 0 to 10mA 120mV
V6A5*30 0 to 5kV 0 to 6mA 150mV
V6A10*30 0 to 10kV 0 to 3mA 400mV
V6A15*30 0 to 15kV 0 to 2mA 900mV
V6A20*30 0 to 20kV 0 to 1.5mA 1.0V
V6A30*30 0 to 30kV 0 to 1mA 1.8V

*Specify “P” for positive polarity or “N” for negative polarity 

V6D MODEL SELECTION TABLE

V6 DC Series Voltage Current Ripple
V6D1*30 0 to 1kV 0 to 30mA 75mV
V6D1.5*30 0 to 1.5kV 0 to 20mA 75mV
V6D3*30 0 to 3kV 0 to 10mA 120mV
V6D5*30 0 to 5kV 0 to 6mA 150mV
V6D10*30 0 to 10kV 0 to 3mA 400mV
V6D15*30 0 to 15kV 0 to 2mA 900mV
V6D20*30 0 to 20kV 0 to 1.5mA 1.0V
V6D30*30 0 to 30kV 0 to 1mA 1.8V

*Specify “P” for positive polarity or “N” for negative polarity

V6A ANALOG/DIGITAL INTERFACE— J1 15 PIN FEMALE D CONNECTOR

Pin Signal Signal Parameters
1 Local Voltage Program Multi-turn front panel potentiometer
2 TX Out (optional) RS232 Receive Data
3 RX In (optional) RS232 Transmit Data
4 Voltage Program Input 0 to 5V=0 to 100% Rated Output, Zin=20MΩ
5 Signal Ground RS232 Ground (optional)
6 Signal Ground Ground
7 +5V Reference Out +5V @ 1mA Max.
8 HV Enable Input Active Low to Enable the HV
9 Current Program Input 0 to 5V=0 to 100% Rated Output, Zin=20MΩ
10 Current Monitor 0 to 5V=0 to 100% Rated Output, Zout=10kΩ
11 Voltage Monitor 0 to 5V=0 to 100% Rated Output, Zout=10kΩ
12 HV Enable Output Active Low HV is Enabled
13 Signal Ground Ground
14 N/C No Connection
15 N/C No Connection

V6D ANALOG/DIGITAL INTERFACE— J1 15 PIN FEMALE D CONNECTOR

Pin Signal Signal Parameters
1 Local Voltage Program Multi-turn front panel potentiometer
2 TX Out (optional) RS232 Receive Data
3 RX In (optional) RS232 Transmit Data
4 Voltage Program Input 0 to 5V=0 to 100% Rated Output, Zin=20MΩ
5 Signal Ground RS232 Ground (optional)
6 Signal Ground Ground
7 +5V Reference Out +5V @ 1mA Max
8 HV Enable Input Active Low to Enable the HV
9 Current Program Input 0 to 5V=0 to 100% Rated Output, Zin=20MΩ
10 Current Monitor 0 to 5V=0 to 100% Rated Output, Zout=10kΩ
11 Voltage Monitor 0 to 5V=0 to 100% Rated Output, Zout=10kΩ
12 HV Enable Output Active Low HV is Enabled
13 +24V Return Input Voltage Return
14 +24Vdc Input Input Voltage 24V±10%, 2A
15 +24Vdc Input Input Voltage 24V±10%, 2A

表和图

DIMENSIONS: in.[mm]

V6-AC 

TOP VIEW

V6 Precision High Voltage Power Supply (Image 3)

SIDE VIEW

V6 Precision High Voltage Power Supply (Image 5)

BOTTOM VIEW

V6 Precision High Voltage Power Supply (Image 7) 

V6 Precision High Voltage Power Supply (Image 9)

V6-DC 

TOP VIEW

V6 Precision High Voltage Power Supply (Image 4)

SIDE VIEW

V6 Precision High Voltage Power Supply (Image 6)

BOTTOM VIEW

V6 Precision High Voltage Power Supply (Image 8)

V6 Precision High Voltage Power Supply (Image 10)