
CZE2000 自动反转模块化高压电源 | Spellman 高压电源
斯派曼CZE2000 模块化的高压电源是OEM 应用的理想之选。专门设计用于需要热切换可逆输出电压的应用。电源的输出极性,通过在接口连接器上提供极性控制信号能快速并安全地反转。
输出电压和电流是完全可调的,通过接地参考远程编程信号如:0 至10Vdc 对应0 至100% 额定输出电压和电流。
远程监测功能是通过电压和电流测试点提供,如:0 至10Vdc 对应0 至100% 额定电压和电流。此外远程极性和模式指示器提供一个全面的电源概览操作。
卓越的负载和输入调节规格与出色的稳定性和低纹波保证了一个稳定的高压输出,实现了一致的工艺效果。
典型应用:
- 静电纺丝
- 质谱分析
- 毛细管电泳
- 静电研究
规格
(Ref. 128076-001 REV. G)
Input Voltage:
24Vdc, ±10%
Input Current:
Less than 1 amp
Efficiency:
75% typical
Output Voltage:
See selection table
Output Current:
See selection table
Polarity:
Auto reversible via command
Power:
10 watts, maximum
Line Regulation:
0.01% for a 10% input voltage change
Load Regulation:
0.01% for a full load change
Ripple:
0.1% Vp-p
Stability:
0.02% per 8 hours (after 1/2 hr warmup)
NL Time Constant:
100ms
Stored Energy:
0.2 Joules at 30kV
Temperature Coefficient:
100ppm/°C
Operating Temperature:
0°C to 40°C
Storage Temperature:
-40°C to 85°C
Humidity:
10% to 85% RH, non condensing
Cooling:
Convection cooled
Dimensions:
3.5”H x 5”W x 10”D (8.9cm x 12.7cm x 25.4cm).
Weight:
6.2lbs. (2.8kg)
Interface Connector:
25 pin male D connector
HV Output Connector:
Detachable 36. (0.91m) cable provided
Regulatory Approvals:
Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive. UL/CUL recognized file E148969
CZE2000 SELECTION TABLE
Maximum Rating | Model Number | |
---|---|---|
kV | mA | |
5 | 2.0 | CZE 5PN10 |
10 | 1.0 | CZE 10PN10 |
15 | 0.67 | CZE 15PN10 |
20 | 0.50 | CZE 20PN10 |
30 | 0.30 | CZE 30PN10 |
CZE2000 25 PIN MALE D CONNECTOR
Pin | Signal | Parameters |
---|---|---|
1 | +24Vdc Return | Power Return |
2 | +24Vdc Return | Power Return |
3 | +24Vdc Return | Power Return |
4 | HV Enable/Inhibit | Open or <1Vdc = HV OFF, >3.4Vdc (up to 15Vdc) = HV ON1 |
5 | Voltage Test Point | 0 to 10Vdc = 0 to 100% rated output, Zout =10kΩ, 1% |
6 | Current Test Point | 0 to 10Vdc = 0 to 100% rated output, Zout =10kΩ, 1% |
7 | Chassis Ground | Ground |
8 | Remote Voltage Control | 0 to 10Vdc = 0 to 100% Rated Output, Zin =10MΩ |
9 | Remote Current Control | 0 to 10Vdc = 0 to 100% Rated Output, Zin =10MΩ |
10 | +10Vdc Reference Output | +10Vdc, 4mA maximum |
11 | Signal Return | Signal Return |
12 | Polarity Control | Open or >3.4Vdc (up to 15Vdc) = Positive Polarity. Grounded or <1Vdc = Negative Polarity |
13 | Positive Polarity Indicator | +24Vdc sourced through a 100Ω series limiting resistor. +24Vdc = active signal |
14 | +24Vdc Input | Power Input |
15 | +24Vdc Input | Power Input |
16 | Chassis Ground | Ground |
17 | Negative Polarity Indicator | +24Vdc sourced through a 100Ω series limiting resistor. +24Vdc = active signal |
18 | I Mode Indicator | Open collector pulled up internally to +15Vdc through 2.7kΩ resistor with a 470Ω limiting resistor in series. Transistor OFF = signal active |
19 | V Mode Indicator | Open collector pulled up internally to +15Vdc through 2.7kΩ resistor with a 470Ω limiting resistor in series. Transistor OFF = signal active |
20 | Return Current Test Point | 0 to 10Vdc = 0 to 100% rated output current, as measured returned from load. Zout =10kΩ, 1% |
21 | Load Return | High Voltage Return Point. Required for GFI circuit functionality |
22 | Ground Fault Indicator | Open collector pulled up internally to +15Vdc through 4.7kΩ resistor with a 470Ω limiting resistor in series. Transistor OFF = signal active |
23 | Spare | No Connection |
24 | Spare | No Connection |
25 | Spare | No Connection |
表和图
DIMENSIONS: in.[mm]
FRONT VIEW
TOP VIEW
BOTTOM VIEW
Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.