ML1350

  • 四路输出高压电源
  • 低成本,紧凑的空气绝缘设计
  • 提供远程启用控制
  • 通过 UL61010-1 认证

*注意:所有规格如有变更,恕不另行通知。有关最新修订,请参阅本数据表的英文 PDF 版本

CE RU 标识

质谱高压电源

斯派曼ML1350 电源模块专为驱动质谱分析中使用的四极而设计。此紧凑的、低成本、SMT 基础的高性能模块是印刷电路板安装。四路输出电源是四极驱动和静电电子透镜的理想之选。

此款电源具有电压调节、电流限制、固定四路输出等特点,每路输出提供高达15mA 的负载电流。ML1350 具有全面的电弧和短路条件保护。接地金属外壳提供了屏蔽和散热功能。提供一个启用特性,允许简单的远程操作。ML1350已有CE 和UL 认证。

典型应用:

  • 四极高压电源
  • 静电电子透镜

CE RU Marking

规格

(Ref. 128037-001 REV. J)

Input Voltage:

+24 Vdc, ±1.2Vdc

Input Current:

≤ 3.0 amps

Output Voltage:

Output 1-Positive:

+245 volts, fixed, accuracy <±10%

Output 2-Negative:

-245 volts, fixed, accuracy <±10%

Output 3-Positive:

+1350 volts, fixed, accuracy <±7%

Output 4-Negative:

-1350 volts, fixed, accuracy <±7% 

Output Current:

15mA maximum for each output

Line Regulation: (typical)

±1 volt all outputs

Load Regulation: (typical)

±3% all outputs

Output Current Limit:

An auto-recovering short circuit fold back limit is employed. Fully arc protected, capable of 10 arcs in 5 seconds.

Ripple:

≤ 0.1% p-p of full rated output voltage

Stability:

 ≤ 0.25% per hour, constant operating conditions after 1 hour warm up.

Under Voltage Shutdown:

The power supply will shut down when an input under voltage condition is detected. When the input voltage is restored above 11.8 volts, operating the enable pin will reset this fault.

Temperature Coefficient:

≤ 200ppm per degree C

Environmental:

Temperature Range:

Operating: 0°C to 50°C

Storage: -35°C to 85°C

Humidity:

10% to 90% RH, non-condensing

Cooling:

Unit must be mounted in free air, in any position with the exception of inverted (pins up). Forced air cooling is recommended.

Dimensions:

0.984. H X 4.331. W X 3.150. D (25mm x 110mm x 80mm) Width does not include mounting tab

Weight:

7.27 oz. (206g)

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive.

表和图

DIMENSIONS: in.[mm]

TOP VIEW

ML1350 质谱分析高压电源 (Image 2)

FRONT VIEW

ML1350 质谱分析高压电源 (Image 3)

SIDE VIEW

ML1350 质谱分析高压电源 (Image 4)

ML1350 质谱分析高压电源 (Image 5)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.