EPM 系列

  • 紧凑的封装
  • 电压和电流编程从零到额定输出
  • 输出电流和电压的测试点
  • 过压保护
  • 通过开启/关闭信号控制输出
  • 提供OEM 定制

30W 高压电源

EPM 系列高压电源是一个高效、紧凑的设计,提供了非常好的调节、低纹波高压。

通过最先进的离线谐振变换器大大减少了这个模块系列的大小。谐振变换器利用一种独特的控制方案,其允许恒频操作,同时保持高效率。高的开关频率允许非常低的纹波和卓越的动态响应能力。

输出电压和电流在全操作范围是可控的。电压和电流编程和监测信号都是0-10Vdc 对应0 至100% 额定输出。一个高压禁用/启用信号允许简单的开/关电源的控制。

典型应用:

  • 电泳
  • 电子束
  • 离子源
  • 光电倍增管
  • 实验应用
  • 静电纺丝

CE Marking

规格

(Ref. 128003-001 REV. J)

Input:

+24Vdc ±10%

Output:

8 models from 1kV to 30kV. Each model is available in positive or negative polarity output.

Voltage Regulation:

Load: 0.02% of output voltage for a full load change.

Line: 0.01% for ±10% change in input voltage.

Current Regulation:

Load: 0.01% of output current from 0 to rated voltage.

Line: 0.01% of rated current over specified input range.

Ripple:

0.1% p-p of maximum rated output voltage.

Dimensions:

2.06”H x 5.63”W x 5.69”D

(52.32mm x 143mm x 144.53mm)

Weight:

2.2 pounds (1kg)

Input Connector:

9 pin AMP Metri-Mate. Mating connector and pins supplied.

Output Cable:

18” ±1” (457mm) of UL® listed high voltage wire.

Voltage Stability:

0.02% per 8 hours (after 1/2 hour warm-up).

Voltage Temperature Coefficient:

0.01% per °C.

Voltage Test Point:

10Vdc ±2% = maximum rated output.

Current Test Point:

10Vdc ±2% = maximum rated output.

Remote Enable:

3.4Vdc = HV ON.

1.0Vdc or open = HV OFF.

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and 2006/95/EC, the Low Voltage Directive.

EPM SELECTION TABLE

Maximum Rating Model Number
kV mA  
1 30 EPM 1*30
3 10 EPM 3*30
5 6 EPM 5*30
10 3 EPM 10*30
15 2 EPM 15*30
20 1.5 EPM 20*30
25 1.2 EPM 25*30
30 1 EPM 30*30

 *Specify “P” for positive polarity or “N” for negative polarity.

CONNECTOR 9 PIN

Pin Signal Parameters
1 Power Ground Power Ground
2 +24Vdc +24Vdc @ 1.85 amps, maximum
3 High Voltage Enable/Inhibit 0Vdc = HV OFF, +5Vdc = HV ON (see manual for details)
4 Voltage Test Point 0 to 10Vdc = 0 to 100% rated output, Zout = 10kΩ
5 Current Test Point 0 to 10Vdc = 0 to 100% rated output, Zout = 10kΩ
6 Voltage Programming 0 to 10Vdc = 0 to 100% rated output, Zin = 10MΩ
7 Current Programming 0 to 10Vdc = 0 to 100% rated output, Zin = 10MΩ
8 +10Vdc Reference +10Vdc @ 1mA maximum
9 Signal Ground Signal Ground

表和图

DIMENSIONS: in.[mm]

SIDE VIEW

EPM 系列 30W 高压电源 (Image 1)

TOP VIEW

EPM 系列 30W 高压电源 (Image 3)

FRONT VIEW

EPM 系列 30W 高压电源 (Image 4)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.