DXM100 系列

  • 100kV @ 1200W
  • 紧凑、重量轻模块电源
  • 通用输入、功率因数校正
  • 标准的数字接口:USB、以太网和RS-232
  • 可编程的功率跳闸特性
  • 符合 CE 认证

1200W 工业X射线发生器

斯派曼新的DXM100 X 射线发生器模块是专门为OEM应用而设计,输出电压高达100kV,功率为1200W。通用的输入、小的封装尺寸和精选的三个标准的数字接口,使得DXM100 能更简化地集成到您的X 射线分析系统中。基于DSP 发射控制电路提供了极好的发射电流调节,且具有出色的稳定性能。

典型应用:

  • NDT 分析
  • 镀层测量
  • 矿物分析
  • 水晶检验
  • 钻石检验
  • 食物生产检验

CE ROHS RU Marking

规格

(Ref. 128107-001 REV. F)

Input Voltage:

Power factor corrected input, ≥ 0.98 180-264Vac, 47-63Hz, 8.25A maximum

Output Voltage:

100kV, maximum

Output Polarity:

Negative-for floating filament X-Ray tubes 

Output Current:

12mA maximum

Output Power:

1200 Watts maximum

Output Voltage Regulation:

≤ 0.01% of rated output voltage over specified input voltage range

≤ 0.01% of rated output voltage for a full load change

Emission Current Regulation:

≤ 0.01% of rated output current over specified input voltage range

≤ 0.01% of rated output current for a change from 30% to 100% of rated output voltage

Filament is disabled when kV is <30% of full scale output 

Ripple:

≤ 1%rms at >20 kHz, 0.1%rms below 20 kHz

Stability:

≤ 25ppm/hr after a 2 hour warm up

Temperature Coefficient:

≤ 50ppm per degree C

Environmental:

Temperature Range:

Operating: 0°C to 40°C

Storage: -40°C to 85°C

Humidity:

20% to 85% RH, non-condensing.

Filament Configuration:

Closed loop emission control regulates filament setting 
to provide desired X-Ray tube emission current.

Output: 5.0 amps at a compliance of 10.0 volts, maximum. The filament loop is disabled when the kV output is less than 30% of full scale output to protect the X-Ray tube. Other filament levels available on special order. 

Control Interface:

Local Interface:

Potentiometers are provided to adjust filament limit and preheat levels

Remote Interface:

USB, Ethernet and RS-232 are standard. All digital monitors have an accuracy specification of 2%

Control Software:

A Windows graphical user interface example is provided. Built-in diagnostics can be performed over Ethernet via a Java applet and any standard web browser

High Voltage Enable:

A hardware based, dry contact closure will enable the power supply into the high voltage on mode

Monitor Signals:

Voltage and current monitor signals are scaled 0-10Vdc equals 0-100% of full scale, accuracy is 1%

Over Power Fault:

 The maximum power the unit can supply can be programmed (0-1200 watts) via the digital interface, this setting will be stored in memory. An over power fault will occur if the output power is ≥ 105% of the set point value. When an over power fault occurs the high voltage output will be disabled and the Over Power Fault indictor will be activated on the GUI/Applet. Additionally both the UV and OV fault LED’s on the DXM100 will be illuminated.

Cooling:

Forced air

Dimensions:

6.25. H X 12. W X 15.5. D (158.75mm x 304.79mm x 393.7mm)

Weight:

43 pounds (19.5kg)

Input Line Connector:

IEC320 with EMI filter, 6´ (1.83 meter) cord set provided

Output Connector:

CA10 (R10). See table for pin out information

Regulatory Approvals:

Compliant to 2004/108/EC, The EMC Directive and 2006/95/EC, The Low Voltage Directive. UL/CUL recognized file E227588. Compliant to 2002/95/EC, RoHS.

DXM100 ANALOG INTERFACE—J2 15 PIN MALE D CONNECTOR

Pin Signal Signal Parameters
1 Power Supply Fault Open Collector, 35V @ 10mA Maximum
2 Current Program In 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
3 Voltage Program In 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
4 Filament Limit Input 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
5 Local Filament Limit Multi-turn front panel potentiometer
6 Filament Preheat Input 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
7 Local Filament Preheat Multi-turn front panel potentiometer
8 Voltage Monitor 0 to 10V=0 to 100% Rated Output, Zout =4.99k, 1%
9 Signal Ground Ground
10 Current Monitor 0 to 10V=0 to 100% Rated Output, Zout =4.99k, 1%
11 X-ray Enable Input Connect to Pin 12 to HV Enable Supply
12 X-ray Enable Output +15V @ Open, ≤15mA @ Closed
13 Filament Monitor 1 Volt=1 Amp, Zout=10kΩ
14 X-ray On Output Signal Open Collector, 35V @10mA Maximum
15 Spare NC

RS-232 DIGITAL INTERFACE—J3 9 PIN FEMALE D CONNECTOR

Pin Signal Signal Parameters
1 NC No Connection
2 TX out Transmit Data
3 RX in Receive Data
4 NC No Connection
5 SGND Ground
6 NC No Connection
7 NC No Connection
8 NC No Connection
9 NC No Connection

USB DIGITAL INTERFACE—J4 4 PIN USB "B" CONNECTOR

Pin Signal Signal Parameters
1 VBUS +5 Vdc
2 D- Data -
3 D+ Data +
4 GND Ground

ETHERNET DIGITAL INTERFACE—J5 8 PIN RJ45 CONNECTOR

Pin Signal Signal Parameters
1 TX+ Transmit Data +
2 TX- Transmit Data -
3 RX+ Receive Data +
4 NC No Connection
5 NC No Connection
6 RX- Receive Data -
7 NC No Connection
8 NC No Connection

J6 CA10 (R10) HV CONNECTOR

Pin Output Connection
C (common) High Voltage Output
S (small) High Voltage Output
L (large) Filament Output

Note: No high voltage cable is provided

表和图

DIMENSIONS: in.[mm]

BOTTOM VIEW

DXM100 系列 1200W 工业X射线发生器 (Image 3)

FRONT VIEW

DXM100 系列 1200W 工业X射线发生器 (Image 4)

SIDE VIEW

DXM100 系列 1200W 工业X射线发生器 (Image 5)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.