DXB Series 300-1200W Промышленные рентгеновские генераторы (featured)

DXB СЕРИЯ

  • Биполярные выходы в одном блоке
  • Компактность и малый вес
  • Модели от 40 кВ до 140 кВ, 300 Вт, 600 Вт и 1200 Вт
  • Универсальный вход, коррекция коэффициента мощности
  • Стандартные цифровые интерфейсы: USB, Ethernet и RS-232
  • Соответствует требованиям CE, UL

* Примечание: Все спецификации могут быть изменены без предварительного уведомления. Пожалуйста, ознакомьтесь с английской версией PDF этой спецификации для получения последней актуальной информации об оборудовании.

300-1200W Промышленные рентгеновские генераторы

Модули биполярных рентгеновских генераторов серии DXB предназначены для применения OEM-производителями в системах с напряжением до 320 кВ (±160 кВ) при мощности 1200 Вт. Универсальный вход, малый размер корпуса и возможность выбора из трех стандартных цифровых интерфейсов упрощают интеграцию устройств серии DXB в Вашу рентгеновскую аналитическую систему. Схема управления эмиссией на базе цифрового сигнального процессора обеспечивает превосходную регулировку тока эмиссии и непревзойденную стабильность выходных характеристик.

Типовые применения:

  • Сортировка пластмасс
  • Исследование кристаллов
  • Измерение гальванических покрытий
  • Толщинометрия
  • Контроль пищевых продуктов
  • Минералогический анализ
  • Рентгеновская люминесценция
  • Рентгеновская дифрактоскопия

CE ROHS RU Marking

Технические характеристики

(Ref. 128100-001 REV. N)

Input Voltage:

Power factor corrected input

100-240Vac, ±10% (90-264Vac):
47-63Hz @ 5.7A for 300 watt units

200-240Vac, ±10% (180-264Vac):
47-63Hz @ 4.8A for 600 watt units
47-63Hz @ 8.0A for 1200 watt units

Output Voltage: 

7 models: 40kV, 60kV, 80kV, 100kV, 120kV, 140kV and 320kV

Output Polarity:

± bipolar output, filament referenced to negative output

Power:

3 power ranges available—300 watts, 600 watts 
and 1200 watts

Other power levels available on special order.

Output Voltage Regulation:

≤ 0.01% of rated output voltage over specified input voltage range

≤ 0.01% of rated output voltage for a full load change

Emission Current Regulation:

≤ 0.01% of rated output current over specified input voltage range

≤ 0.01% of rated output current for a change from 30% to 100% of rated output voltage

Filament is disabled when kV is <30% of full scale output 

Ripple:

≤ 1%rms at >20 kHz, 0.1%rms below 20 kHz

Stability:

≤ 25ppm/hr after a 2 hour warm up

Temperature Coefficient:

≤ 50ppm per degree C

Environmental:

Temperature Range:

Operating: 0°C to 40°C

Storage: -40°C to 85°C

Humidity: 

20% to 85% RH, non-condensing.

Filament Configuration:

Closed loop emission control regulates filament setting to provide desired X-Ray tube emission current.

Floating Filament (ac output referenced to negative output voltage).

Output:

0-5 amps at a compliance of 10 volts, maximum. The filament loop is disabled when the kV output is less than 30% of full scale output to protect the X-Ray tube. Other filament levels available on special order.

Control Interface

Local Interface: Potentiometers are provided to adjust filament limit and preheat levels

Remote Interface: USB, Ethernet and RS-232 are standard. All digital monitors have an accuracy specification of 2%

Control Software: A Windows graphical user interface example is provided. 

High Voltage Enable: A hardware based, dry contact closure will enable the power supply into the high voltage on mode

Monitor Signals: Voltage and current monitor signals are scaled 0-10Vdc equals 0-100% of full scale, accuracy is 1%

Cooling:

Forced air

Dimensions:

40-140kV:

4.75˝ H X 12˝ W X 12˝ D (120.65mm x 304.8mm x 304.8mm)

320kV:

10.5˝ H X 19.0˝ W X 21.5˝ D (266.7mm x 482.6mm x 546.1mm)

Weight:

40-140kV: 26 pounds (11.8kg)

320kV: 150 pounds (68kg)

Input Line Connector:

IEC320 with EMI filter

Output Connectors:

40-140kV:

Claymount Mini Federal Standard X-Ray connectors.

Other connectors and pinouts available on special order.

320kV:

R24 X-Ray connectors.

Other connectors and pinouts available on special order.

Regulatory Approvals:

Compliant to EEC EMC Directive. Compliant to EEC Low Voltage Directive. UL/CUL recognized, File E227588. RoHS Compliant. DXB320PN1200 is not UL recognized.

DXB SELECTION TABLE— 300W, 600W, 1200W

300 Watt 600 Watt 1200 Watt
kV mA Model mA Model mA Model
40 7.50 DXB40PN300 15.0 DXB40PN600 30.0 DXB40PN1200
50 5.00 DXB60PN300 10.0 DXB60PN600 20.0 DXB60PN1200
80 3.75 DXB80PN300 7.50 DXB80PN600 15.0 DXB80PN1200
100 3.00 DXB100PN300 6.00 DXB100PN600 12.0 DXB100PN1200
120 2.50 DXB120PN300 5.00 DXB120PN600 10.0 DXB120PN1200
140 2.14 DXB140PN300 4.28 DXB140PN600 8.57 DXB140PN1200
 320  Not Available  Not Available  3.75  DXB320PN1200

DXB ANALOG INTERFACE— J2 15 PIN MALE D CONNECTOR

Pin Signal Signal Parameters
1 Power Supply Fault Open Collector, 35V @ 10mA Maximum
2 Current Program In 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
3 Voltage Program In 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
4 Filament Limit Input 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
5 Local Filament Limit Multi-turn front panel potentiometer
6 Filament Preheat Input 0 to 10V=0 to 100% Rated Output, Zin=10MΩ
7 Local Filament Preheat Multi-turn front panel potentiometer
8 Voltage Monitor 0 to 10V=0 to 100% Rated Output, Zout =4.99k, 1%
9 Signal Ground Ground
10 Current Monitor 0 to 10V=0 to 100% Rated Output, Zout =4.99k, 1%
11 X-ray Enable Input Connect to Pin 12 to HV Enable Supply
12 X-ray Enable Output +15V @ Open, ≤15mA @ Closed
13 Filament Monitor 1 Volt=1 Amp, Zout=10kΩ
14 X-ray On Output Signal Open Collector, 35V @10mA Maximum
15 Spare N/C

RS-232 DIGITAL INTERFACE— J3 9 PIN FEMALE D CONNECTOR

Pin Signal Signal Parameters
1 N/C No Connection
2 TX out Transmit Data
3 RX in Receive Data
4 N/C No Connection
5 SGND Ground
6 N/C No Connection
7 N/C No Connection
8 N/C No Connection
9 N/C No Connection

USB DIGITAL INTERFACE— J4 4 PIN USB "B" CONNECTOR

Pin Signal Signal Parameters
1 VBUS +5 Vdc
2 D- Data -
3 D+ Data +
4 GND Ground

ETHERNET DIGITAL INTERFACE— J5 8 PIN RJ45 CONNECTOR

Pin Signal Signal Parameters
1 TX+ Transmit Data +
2 TX- Transmit Data-
3 RX+ Receive Data +
4 NC No Connection
5 NC No Connection
6 RX- Receive Data
7 NC No Connection
8 NC No Connection

CLAYMOUNT HV CONNECTOR PINOUT J6 CATHODE OUTPUT

Pin Output Connection
C (common) -High Voltage Output
S (small) -High Voltage Output
L (large) Filament Output
G (grid) Filament Output

CLAYMOUNT HV CONNECTOR PINOUT J7 ANODE OUTPUT

Pin Output Connection
C (common) +High Voltage Output
S (small) +High Voltage Output
L (large) +High Voltage Output
G (grid) +High Voltage Output

Note: No high voltage cable is provided

Recommended Cable:

Claymount part number: 12096

Cable assembly, L3 CA11, CA11, 10F, CS=Bare 10 foot,

Mini Federal Connectors on both ends, "C" and "S" are both connected to the bare wire

Таблицы и диаграммы