XRBC

  • Integrated HV Supply, Filament Supply, X-Ray
    Tube, Beam Port and Control Electronics
  • Universal Input, Power Factor Corrected
  • Can be Mounted in any Physical Orientation
  • Ethernet and Standard RS-232 Digital Interface

170-480W Monoblock® 工業用X線ジェネレーター

Spellman’s XRBC Series of Monoblock® X-Ray sources are designed for OEM applications powering its internal X-Ray tube up to 160kV at 170W, or 160kV at 480W with an oil cooler. Features like universal input, small package size with Ethernet and RS-232 digital interface simplify integrat­ing the XRBC into your X-Ray system. Standard models are available either with fan shaped or cone shaped beam geometries. Proprietary emission control circuitry provides excellent regulation of X-Ray tube current, along with out­standing stability performance.

Typical applications:

Scanning, Security Applications

Specifications

(Ref. 128111-001 REV. B)

X-Ray Characteristics:

Tube Type: Glass tube, Tungsten target, Be filter

Focal Spot: 0.8mm x 0.8mm

Beam Filter: 1.7mm Glass, typical + 12mm oil + 3mm PEEK, 0.8 Be

Beam Geometry: Fan up to 80° x 10° nominal or cone beam up to 40°

Input Voltage:

480W Single phase - 90-264Vac, 50/60Hz, 8 amps, maximum. IEC320 input connector with EMI filter

170W Single phase - 90-264Vac, 50/60Hz, 3.15 amps,

X-Ray Tube Voltage: 

Nominal X-Ray tube voltage is adjustable between 80kV to 160kV

X-Ray Tube Current:

0.5mA to 1.2mA over specified tube voltage range (up to 3mA available upon request with oil cooler)

X-Ray Tube Power:

170W, maximum continuous, or 480W with oil cooler 

Voltage Regulation:

Line: ±0.1% for a ±10% input line change of nominal input line voltage

Load: ±0.1% for a 10% to full load change

Voltage Accuracy:

Voltage measured across the X-Ray tube is within ±2% of the programmed value

Voltage Risetime:

Ramp time shall be <350 msec from 10% to 90% of rated output 

Voltage Overshoot:

Within 2% of rated voltage 

Voltage Ripple:

0.1% pp of rated voltage from 10 Hz to 10kHz across X-Ray tube

Current Regulation:

Line: 0.1% over a range of line voltage from 90 to 264Vac

Load: <0.5% @ 80-160kV, 0.1mA to 3mA

Current Accuracy:

Current measured through the X-Ray tube is within ±2% of the programmed value 

Current Risetime:

<350 msec from 10% to 90% of rated output 

Arc Intervention:

200mS quench with a 4 arcs in 10 seconds shutdown

Filament Configuration:

High frequency AC filament drive; referenced to cathode potential of the X-Ray tube. Closed loop filamentary emission control circuit regulates filament current to provide desired X-Ray tube emission current.

Digital Interface:

Ethernet and RS-232

Operating Temperature:

0°C to +40°C

Storage Temperature:

-30°C to +70°C

Humidity:

5% to 95% relative humidity, non-condensing

Cooling:

170W unit: Customer provided convection/external forced air to keep oil temperature <>

480W unit: Heat exchanger w/fan and oil pump, powered from customer provided 115Vac

Grounding Point:

8-32 ground stud provided on chassis

Dimensions:

See line drawings 1, 2

Weight:

170W unit: <150 lbs (68.0 kg)

480W unit: <180 lbs (81.64 kg 

Orientation:

Can be mounted in any orientation.

X-Ray Leakage:

Not to be greater than 0.5mR/hr at 5cm from surface of the Monoblock® when operating at maximum rated kV and maximum rated X-Ray tube power.

RS-232 DIGITAL INTERFACE—9 PIN MALE D CONNECTOR

Pin Signal Parameters
1 N/C No Connection
2 TX Transmit Data
3 RX Receive Data
4 N/C No Connection
5 SGND Signal Ground
6 N/C No Connection
7 N/C No Connection
8 N/C No Connection
9 N/C No Connection

ETHERNET DIGITAL INTERFACE—RJ45 8 PIN FEMALE CONNECTOR

Pin Signal Parameters
1 TX + Transmit Data +
2 TX - Transmit Data -
3 RX + Receive Data +
4 N/C No Connection
5 N/C No Connection
6 RX - Receive Data -
7 N/C No Connection
8 N/C No Connection

ANALOG INTERFACE—J4 15 PIN FEMALE D CONNECTOR

Pin Signal Parameters
1 N/C No Connection
2 N/C No Connection
3 Enable +24Vdc (>20Vdc) = HV ON
4 Signal Ground Ground
5 kV Monitor 0-4.5Vdc = 0 to 100% rated output, Zin = 10kΩ
6 N/C No Connection
7 mA Monitor 0-4.5Vdc = 0 to 100% rated output, Zin = 10kΩ
8 Interlock Dry contact to ground (10mA) = interlock closed
9 Signal Ground Ground
10 N/C No Connection
11 Signal Ground Ground
12 HV ON Lamp Relay Normally open, X-Ray ON = closed,
30Vdc @ 1A maximum
13 HV ON Lamp Relay Common dry contact, 30Vdc @ 1A maximum
14 HV ON Lamp Relay Normally closed, X-Ray ON = open,
30Vdc @ 1A maximum
15 Power Supply Fault Open collector, 35Vdc @ 10mA maximum,
High = no fault, series Zin = 1kΩ

LED INDICATORS

Indicator Color  
POWER GREEN Power is ON
X-RAY ON YELLOW X-Rays are enabled
FAULT RED Fault
INTERLOCK WHITE Interlock closed
ARC FAULT RED Momentarily illuminated for 1 ARC, Continuous
for arc shutdown after multiple arcs
OVER VOLTAGE RED Over Voltage fault occurs
UNDER VOLTAGE RED Under Voltage fault occurs
OVER CURRENT RED Over Current fault occurs
UNDER CURRENT RED Under Current fault occurs
OVER TEMP RED Over Temperature fault occurs

Tables & Diagrams

DIMENSIONS: in.[mm]

XRBC 170W UNIT

FRONT VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 2)

TOP VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 3)

SIDE VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 4)

XRBC 480W UNIT

FRONT VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 5)

TOP VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 6)

SIDE VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 7) 

CONTROLLER

FRONT VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 8)

                  SIDE VIEW                                                          TOP VIEW

XRBC Monoblock® 工業用X線ジェネレーター (Image 9)                 XRBC Monoblock® 工業用X線ジェネレーター (Image 10)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.