SERIE XRB302

  • Fuente de alto voltaje con alimentación de filamento, tubo de rayos X, puerto de haz y electrónica de control integrados
  • Compacta y ligera
  • Se puede montar en cualquier orientación física
  • Interfaz digital estándar RS-232

GENERADORES DE RAYOS X INDUSTRIALES XRB302 MONOBLOCK®

La serie XRB0302 de fuentes de rayos X Monoblock® de Spellman está diseñada para aplicaciones de OEM en las cuales se energiza su tubo interno de rayos X con hasta 160 kV a 320 W Las funciones tales como el tamaño compacto y la interfaz digital RS-232, simplifican la integración de la XRB302 en su sistema de rayos X. Los modelos estándar están disponibles con geometría de haz en forma de abanico. El circuito de control de emisión de diseño propio proporciona una regulación excelente de la corriente del tubo de rayos X, además de una sobresaliente estabilidad y desempeño.

Aplicaciones típicas:

  • Barrido con rayos X: inspección de alimentos
  • Confirmación de nivel de llenado
  • Aplicaciones de seguridad

CE Marking

Especificaciones

(Ref. 128091-001 REV. G)

X-Ray Characteristics:

Tube Type: Glass tube, Tungsten target, Be filter

Focal Spot Options: 0.8mm x 0.8mm, 0.5mm x 0.5mm (IEC 336)

Beam Filter Options: 5052 Al, 0.040" (±0.01"); two pieces of 6061 Al, 0.16" (±0.005")

Beam Geometry:  Asymmetrical fan 105° x 4°, 80°x10°, cone up to 40°

Input Voltage:

200-264Vac, 50/60Hz, 4.0A max

X-Ray Tube Voltage:

Nominal X-Ray tube voltage is adjustable between 80kV to 160kV

X-Ray Tube Current:

0.5mA to 4mA over specified tube voltage range

X-Ray Tube Power:

320A maximum continuous

Voltage Regulation:

Line: ±0.05% for a ±10% input line change

Load: ±0.05% for a 0.5mA to 4mA load change

Voltage Accuracy:

Voltage measured across the X-Ray tube is within ±2% of the programmed value

Voltage Risetime:

Ramp time shall be <500ms from 10% to 90% of rated output 

Voltage Overshoot:

Within 5% of rated voltage in <10ms

Voltage Ripple:

≤ 1% p-p of rated voltage @ 1kHz

Current Regulation:

Line: ±0.5% @ 50-100% V nominal over specified Line range

Load: ±0.5% @ 50-100% V nominal over specified Load range

Current Accuracy:

Current measured through the X-Ray tube is within ±2% of the programmed value

Current Risetime:

<500ms from 10% to 90% of rated output 

Arc Intervention:

4 arcs in 10 seconds = shutdown

Filament Configuration:

Internal high frequency AC filament drive with closed loop filament emission control

Analog Interface:

0 to 10Vdc ground referenced monitoring signals

Digital Interface:

RS-232

Control Software:

A demo GUI for engineering evaluations will be provided for the RS-232 digital interface upon request.

Interlock Signals:

A hardware interlock functions in digital programming modes.

Operating Temperature:

0°C to +40°C

Storage Temperature:

-40°C to +70°C

Humidity:

10% to 90% relative humidity, non-condensing

Cooling:

Heat exchanger w/fan and oil pump

Input Line Connector:

3 pin, Phoenix Contact 1829167

Digital Interface Connector:

9 pin D, female

Analog Monitoring Connector:

10 pin Phoenix Contact 1755503

PIN  SIGNAL  PARAMETERS

1  Line  200-264Vac Input

2  GND  200-264Vac Input

3  Neutral  Neutral

Grounding Point:

8-32 ground stud provided on chassis

Dimensions:

See outline drawing

Weight:

120lbs (54.4kg) maximum

Orientation:

Can be mounted in any orientation.

X-Ray Leakage:

Not to be greater than 0.5mR/hr at 5cm outside the external surface per FDA 21 CFR 1020.40 and OSHA 29 CFR 1020.96

Regulatory Approvals:

Compliant to 2004/108/EC, The EMC Directive and 2006/95/EC, The Low Voltage Directive.

AC INPUT POWER JB11 3 PIN PHOENIX CONTACT

Pin Signal Parameters
1 Line 200-264Vac Input
2 GND 200-264Vac Input
3 Neutral Neutral

RS-232 DIGITAL INTERFACE JB16 9 PIN FEMALE D CONNECTOR

Pin Signal Parameters
1 N/C No Connection
2 TX RS-232 Transmit
3 RX RS-232 Receive
4 N/C No Connection
5 SGND Signal Ground
6 N/C No Connection
7 N/C No Connection
8 N/C No Connection
9 N/C No Connection

ANALOG MONITORING— JB11 10 PIN PHOENIX CONTACT

Pin Signal Parameters
1 X-Ray Enable +24Vdc = Enable X-Ray 0Vdc/Open = Disable X-Rays
2 RTN Signal Return
3 N/C No Connection
4 kV Monitor 0 to 10Vdc = 0 to 100kV, Zout = 10kΩ
5 SGND Signal Return
6 mA Monitor 0 to 10Vdc = 0 to 5mA, Zout = 10kΩ
7 Fault Open Collector, High (Open) = No Fault, 35Vdc @10mA max.
8 HV On Lamp, Relay N/O Relay Normally Open, 50Vdc @ 1A maximum
9 HV On Lamp, Relay Common Relay Common, 50Vdc @ 1A maximum
10 HV On Lamp, Relay N/C Relay Normally Closed, 50Vdc @ 1A maximum

Tablas y Diagramas

DIMENSIONS: in.[mm]

TOP VIEW

XRB302 X-Ray Generator (Image 2)

SIDE VIEW

XRB302 X-Ray Generator (Image 3)

BACK VIEW

XRB302 X-Ray Generator (Image 4)